D200I Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – High Isolation Miniature, 2W SIP DC/DC Converters

Model Selection Guide
Model
Number
D201I
D202I
D203I
D204I
D205I
D206I
D207I
D211I
D212I
D213I
D214I
D215I
D216I
D217I
D221I
D222I
D223I
D224I
D225I
D226I
D227I
D231I
D232I
D233I
D234I
D235I
D236I
D237I
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
367
30
5
4.5 - 5.5
512
30
5
4.5 - 5.5
500
30
5
4.5 - 5.5
500
30
5
4.5 - 5.5
555
30
5
4.5 - 5.5
512
30
5
4.5 - 5.5
500
30
12 10.8 - 13.2 169
20
12 10.8 - 13.2 216
20
12 10.8 - 13.2 203
20
12 10.8 - 13.2 203
20
12 10.8 - 13.2 222
20
12 10.8 - 13.2 203
20
12 10.8 - 13.2 203
20
24 21.6 - 26.4 76
10
24 21.6 - 26.4 105
10
24 21.6 - 26.4 102
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 111
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 101
10
48 43.2 - 52.8 45
6
48 43.2 - 52.8 54
6
48 43.2 - 52.8 53
6
48 43.2 - 52.8 53
6
48 43.2 - 52.8 57
6
48 43.2 - 52.8 52
6
48 43.2 - 52.8 52
6
Voltage
(VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
400.0
165.0
133.0
±200.0
±83.3
±66.6
400.0
400.0
165.0
133.0
±200.0
±83.3
±66.6
400.0
400.0
165.0
133.0
±200.0
±83.3
±66.6
400.0
400.0
165.0
133.0
±200.0
±83.3
±66.6
Current
(mA, Min)
10.0
8.0
3.5
2.7
±4.0
±1.7
±1.4
10.0
8.0
3.5
2.7
±4.0
±1.7
±1.4
10.0
8.0
3.5
2.7
±4.0
±1.7
±1.4
10.0
8.0
3.5
2.7
±4.0
±1.7
±1.4
Load
Regulation
(%, Max)
20
10
10
10
10
10
10
20
10
10
10
10
10
10
20
10
10
10
10
10
10
20
10
10
10
10
10
10
Efficiency
(%, Typ)
72
78
82
82
72
78
80
65
77
82
82
75
82
82
72
79
80
82
75
82
82
60
77
78
78
73
80
80
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
200
200
200
200
200
200
200
100
100
100
100
100
100
100
Other input/output combinations are available
(i.e. 24.0 VDC). Contact the factory for details at:
Capacitive Load
Single Output Dual Output
Pin Connections
Pin Single Dual
[e-mail]
(μF Max)
(μF Max)
1
+Vin
+Vin
Notes:
470
1. Output load regulation is specified for a load change of 20% to 100%.
2. These units do not require external components to operate, but the use of an input ca-
±220
2
-Vin
-Vin
5
-Vout -Vout
6 No Pin Common
pacitor (10 μF) may enhance performance in some applications. It is recommended that an
7
input capacitor of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input
model.
Mechanical Dimensions
An output capacitor (4.7 μF to 220 μF or ±4.7 μF to ±100 μF) may be used to reduce ripple.
+Vout
+Vout
To improve EMI performance, a simple filter network consisting of a 10 uF to 100 uF capaci-
tor and 12 uH inductor should be effective.
3. These units will operate at no load without damage, but may not meet all specifications.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this,
connect the load across the positive (+Vout) and negative (-Vout) outputs and float the
output common.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Derating Curve
MicroPower Direct
www.micropowerdirect.com
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation
on the side of the unit
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]