D200I Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – High Isolation Miniature, 2W SIP DC/DC Converters

D200I Series
High Isolation
Miniature, 2W SIP
DC/DC Converters
Key Features:
• 2W Output Power
• Miniature SIP Case
• Single & Dual Outputs
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input 4.5 5.0 5.5
Input Voltage Range
12 VDC Input 10.8 12.0 13.2
24 VDC Input 21.6 24.0 26.4
VDC
• 3,000 VDC Isolation
• >1.12 MHour MTBF
• 28 Standard Models
• Industry Standard Pin-Out
Input Filter
Reflected Ripple Current
Output
Parameter
48 VDC Input 43.2 48.0 52.8
Internal Capacitor
12 μH Source Inductance
20
mA P - P
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±3.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0
%
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation
See Model Selection Guide
Ripple & Noise (20 MHz)
75
mV P - P
Output Power Protection
120
%
Temperature Coefficient
±0.02 %/ºC
Output Short Circuit
RoHS Compliant _General
Momentary (0.5 Sec.)
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
Isolation Resistance
60 Seconds 3,000
500 VDC 1,000
VDC
MΩ
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
80
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case
+100
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
Weight
0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)
0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.08 Oz (2.3g)
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 1.12
Units
MHours
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
7.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
24 VDC Input -0.7
15.0
VDC
28.0
48 VDC Input -0.7
54.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Internal Power Dissipation
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.