D200ERW Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Low Cost, Miniature 2W SIP, Wide Input DC/DC Con vert ers

Model Selection Guide
Model
Number
D201ERW
D202ERW
D203ERW
D204ERW
D205ERW
D206ERW
D207ERW
D208ERW
D209ERW
D211ERW
D212ERW
D213ERW
D214ERW
D215ERW
D216ERW
D217ERW
D218ERW
D219ERW
D221ERW
D222ERW
D223ERW
D224ERW
D225ERW
D226ERW
D227ERW
D228ERW
D229ERW
D231ERW
D232ERW
D233ERW
D234ERW
D235ERW
D236ERW
D237ERW
D238ERW
D239ERW
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 9.0
508
40
5
4.5 - 9.0
588
40
5
4.5 - 9.0
555
40
5
4.5 - 9.0
547
40
5
4.5 - 9.0
555
40
5
4.5 - 9.0
547
40
5
4.5 - 9.0
597
40
5
4.5 - 9.0
555
40
5
4.5 - 9.0
547
40
12 9.0 - 18.0 191
20
12 9.0 - 18.0 216
20
12 9.0 - 18.0 211
20
12 9.0 - 18.0 206
20
12 9.0 - 18.0 208
20
12 9.0 - 18.0 208
20
12 9.0 - 18.0 222
20
12 9.0 - 18.0 214
20
12 9.0 - 18.0 214
20
24 18.0 - 36.0 96
10
24 18.0 - 36.0 108
10
24 18.0 - 36.0 105
10
24 18.0 - 36.0 103
10
24 18.0 - 36.0 104
10
24 18.0 - 36.0 104
10
24 18.0 - 36.0 109
10
24 18.0 - 36.0 105
10
24 18.0 - 36.0 107
10
48 36.0 - 72.0 48
5
48 36.0 - 72.0 55
5
48 36.0 - 72.0 53
5
48 36.0 - 72.0 52
5
48 36.0 - 72.0 53
5
48 36.0 - 72.0 52
5
48 36.0 - 72.0 55
5
48 36.0 - 72.0 52
5
48 36.0 - 72.0 52
5
Output
Voltage Current Current
(VDC) (mA, Max) (mA, Min)
3.3
500.0
50.0
5.0
400.0
40.0
9.0
222.0
22.0
12.0
166.0
16.0
15.0
133.0
13.0
24.0
83.0
8.0
±5.0 ±200.0
±20.0
±12.0 ±83.0
±8.0
±15.0 ±66.0
±7.0
3.3
500.0
50.0
5.0
400.0
40.0
9.0
222.0
22.0
12.0
166.0
16.0
15.0
133.0
13.0
24.0
83.0
8.0
±5.0 ±200.0
±20.0
±12.0 ±83.0
±8.0
±15.0 ±66.0
±7.0
3.3
500.0
50.0
5.0
400.0
40.0
9.0
222.0
22.0
12.0
166.0
16.0
15.0
133.0
13.0
24.0
83.0
8.0
±5.0 ±200.0
±20.0
±12.0 ±83.0
±8.0
±15.0 ±66.0
±7.0
3.3
500.0
50.0
5.0
400.0
40.0
9.0
222.0
22.0
12.0
166.0
16.0
15.0
133.0
13.0
24.0
83.0
8.0
±5.0 ±200.0
±20.0
±12.0 ±83.0
±8.0
±15.0 ±66.0
±7.0
Efficiency
(%, Typ)
65
68
72
73
72
73
67
72
73
72
77
79
81
80
80
75
78
78
72
77
79
81
80
80
76
79
78
71
75
79
80
79
80
75
80
80
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
700
700
700
700
350
350
350
350
350
350
350
350
350
135
135
135
135
135
135
135
135
135
Mechanical Dimensions ^Notes:
1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be
placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual
output units.
2. These units should not be operated with a load under
10% of full load. Operation at no-load may cause
damage to the unit.
Vin
Input
Capacitor
Vout
Output Capacitor
0 - 70ºC -40 - 85ºC
3. These converters are specified for operation without
(Electrolitic) (Tantalum)
external components. However, in some applications 5 VDC 100 µF 5 VDC 100 µF
47 µF
the addition of input/output capacitors will enhance
stability and reduce output ripple. Recommended
12 VDC
100 µF
9 VDC 100 µF
47 µF
capacitor values are given at right.
24 VDC 10 µF 12 VDC 100 µF 47 µF
Output ripple on single output units may be further
enhanced by using the CS terminal (single output
48 VDC
10 µF
15 VDC 100 µF
47 µF
units operated at 50% load or below should use this function). A
Output Voltage
low ESR capacitor is connected between the CS pin and the -Vout
pin (the capcitor anode connected to the -Vout pin). Recommended
3.3V 5V 9V 12V 15V 24V
capacitor values are given in the table at right. If not used, the CS CS 47 µF - 100 µF 22 µF - 47 µF
pin should be left open.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across
the +Vout and -Vout outputs and float the output common.
5. The remote on/off control pin is referenced to the -Vin pin. Input current
Min
Max
to the pin should be between 5 - 10 mA with a maximum of 20 mA.
6. It is recommended that a fuse be used on the input of a power supply for
On
<0.6 VDC to Open Circuit
protection. See the Model Selection table above for the correct rating. Off 2.7 VDC
15.0 VDC
Derating Curve
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
Pin Connections
Pin Single Dual
1 -Vin
-Vin
2 +Vin +Vin
3 Remote ON/OFF
5 NF
NF
NF = No Function
Pin Single Dual
6 +Vout +Vout
7 -Vout Common
8 CS
-Vout
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]