D200ERU Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Low Cost, 4:1 Input Miniature, 2W SIP DC/DC Converters

Model Selection Guide
Model
Number
D201ERU
D202ERU
D203ERU
D204ERU
D205ERU
D206ERU
D207ERU
D208ERU
D209ERU
D211ERU
D212ERU
D213ERU
D214ERU
D215ERU
D216ERU
D217ERU
D218ERU
D219ERU
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
24 9.0 - 36.0 114
35
24 9.0 - 36.0 111
35
24 9.0 - 36.0 107
35
24 9.0 - 36.0 102
35
24 9.0 - 36.0 103
35
24 9.0 - 36.0 110
35
24 9.0 - 36.0 107
35
24 9.0 - 36.0 102
35
24 9.0 - 36.0 103
35
48 18.0 - 72.0 58
15
48 18.0 - 72.0 55
15
48 18.0 - 72.0 53
15
48 18.0 - 72.0 51
15
48 18.0 - 72.0 52
15
48 18.0 - 72.0 55
15
48 18.0 - 72.0 54
15
48 18.0 - 72.0 51
15
48 18.0 - 72.0 52
15
Voltage
(VDC)
3.3
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
3.3
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current Current
(mA, Max) (mA, Min)
500.0
50.0
400.0
40.0
222.0
22.0
167.0
16.0
133.0
13.0
±200.0
±20.0
±111.0
±11.0
±83.0
±8.0
±67.0
±7.0
500.0
50.0
400.0
40.0
222.0
22.0
167.0
16.0
133.0
13.0
±200.0
±20.0
±111.0
±11.0
±83.0
±8.0
±67.0
±7.0
Efficiency
(%, Typ)
73
75
78
82
81
76
78
82
81
72
76
78
81
80
75
77
81
80
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
200
Derating Curve ^Notes:
1. When measuring output ripple, it is recommended that an external ceramic capacitor
(approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output
units and from each output to common for dual output units.
2. These units should not be operated with a load under 10% of full load. Operation at
no-load may cause damage to the unit.
3. These converters are specified for
operation without external compo-
nents. However, in some applica-
tions the addition of input/output
Vin
Input
Capacitor
Vout
Output
Capacitor
capacitors will enhance stability and
reduce output ripple. Recommended _{12 VDC}
capacitor values are given at right.
Output ripple on single output units
15 VDC
100 µF
100 µF
5 VDC
9 VDC
47 µF
47 µF
may be further enhanced by using 24 VDC 10 µF 12 VDC 47 µF
the CS terminal (single output units
operated at 50% load or below
48 VDC
10 µF
15 VDC
47 µF
should use this function). A low ESR capacitor is connected between the CS pin and the
-Vout pin (the capcitor anode connected to the -Vout pin). Recommended capacitor
values are given in the table at right. If not used, the CS pin should be left open.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do
this, connect the load across the +Vout and -Vout outputs and float the output com-
mon.
5. The remote on/off control pin is referenced to
Min
Max
the -Vin pin. Input current to the pin should
be between 5 - 10 mA with a maximum of 20
On
<0.6 VDC to Open Circuit
mA.
Off 2.7 VDC
15.0 VDC
6. It is recommended that a fuse be used on the
input of a power supply for protection. See the Model Selection
Mechanical Dimensions
table above for the correct rating.
Max. Capacitive Load
Output Voltage
3.3
5
9
12
820 µF 660 µF 470 µF 330 µF
±5
±9
±12
±15
±330 µF ±220 µF ±150 µF ±120 µF
15
220 µF
Pin Connections
Pin Single Dual
1 -Vin
-Vin
2 +Vin +Vin
3 Remote ON/OFF
6 +Vout +Vout
NC = No Connection
Pin Single Dual
7 NC Common
8 NC
NC
9 -Vout -Vout
MicroPower Direct
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]