D200 Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Single & Dual Output Miniature, 2W SIP DC/DC Converters

Model Selection Guide
www.micropowerdirect.com
Input
Model
Number
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
Output
Voltage Current
(VDC) (mA, Max)
Current
(mA, Min)
Load
Regulation
(%, Max)
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
D201
5
4.5 - 5.5
367
30
3.3
400.0
10.0
20
D202
5
4.5 - 5.5
512
30
5.0
400.0
8.0
10
D203
5
4.5 - 5.5
500
30
12.0
165.0
3.5
10
D204
5
4.5 - 5.5
500
30
15.0
133.0
2.7
10
D205
5
4.5 - 5.5
555
30
±5.0 ±200.0
±4.0
10
D206
5
4.5 - 5.5
512
30
±12.0
±83.3
±1.7
10
D207
5
4.5 - 5.5
500
30
±15.0
±66.6
±1.4
10
D211
12 10.8 - 13.2 169
20
3.3
400.0
10.0
20
D212
12 10.8 - 13.2 216
20
5.0
400.0
8.0
10
D213
12 10.8 - 13.2 203
20
12.0
165.0
3.5
10
D214
12 10.8 - 13.2 203
20
15.0
133.0
2.7
10
D215
12 10.8 - 13.2 222
20
±5.0 ±200.0
±4.0
10
D216
12 10.8 - 13.2 203
20
±12.0
±83.3
±1.7
10
D217
12 10.8 - 13.2 203
20
±15.0
±66.6
±1.4
10
D221
24 21.6 - 26.4 76
10
3.3
400.0
10.0
20
D222
24 21.6 - 26.4 105
10
5.0
400.0
8.0
10
D223
24 21.6 - 26.4 102
10
12.0
165.0
3.5
10
D224
24 21.6 - 26.4 101
10
15.0
133.0
2.7
10
D225
24 21.6 - 26.4 111
10
±5.0 ±200.0
±4.0
10
D226
24 21.6 - 26.4 101
10
±12.0
±83.3
±1.7
10
D227
24 21.6 - 26.4 101
10
±15.0
±66.6
±1.4
10
D231
48 43.2 - 52.8 45
6
3.3
400.0
10.0
20
D232
48 43.2 - 52.8 54
6
5.0
400.0
8.0
10
D233
48 43.2 - 52.8 53
6
12.0
165.0
3.5
10
D234
48 43.2 - 52.8 53
6
15.0
133.0
2.7
10
D235
48 43.2 - 52.8 57
6
±5.0 ±200.0
±4.0
10
D236
48 43.2 - 52.8 52
6
±12.0
±83.3
±1.7
10
D237
48 43.2 - 52.8 52
6
±15.0
±66.6
±1.4
10
72
1,000
78
1,000
82
1,000
82
1,000
72
1,000
78
1,000
80
1,000
65
500
77
500
82
500
82
500
75
500
82
500
82
500
72
200
79
200
80
200
82
200
75
200
82
200
82
200
60
100
77
100
78
100
78
100
73
100
80
100
80
100
Other input/output combinations are available
(i.e. 24.0 VDC). Contact the factory for details at:
Capacitive Load
Single Output Dual Output
Pin Connections
Pin Single Dual
[e-mail]
(µF Max)
(µF Max)
1
+Vin
+Vin
Notes:
470
1. Output load regulation is specified for a load change of 20% to 100%.
2. These units do not require external components to operate, but the use of an input capacitor (10 µF)
may enhance performance in some applications. It is recommended that an input capacitor of 4.7 µF
to 47µF (dependent upon the application) be used on 48V input model.
An output capacitor (4.7 µF to 220 µF or ±4.7 µF to ±100 µF) may be used to reduce ripple. To improve
EMI performance, a simple filter network consisting of a 10 µF to 100 µF capacitor and 12 µH inductor
±220
2
4
5
6
Mechanical Dimensions
-Vin
-Vout
No Pin
+Vout
-Vin
-Vout
Common
+Vout
should be effective.
3. These units will operate at no load without damage, but may not meet all specifications.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the
load across the positive (+Vout) and negative (-Vout) outputs and float the output common.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Derating Curve
MicroPower Direct
We Power Your Success - For Less!
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation
on the side of the unit
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]