English
Language : 

D200 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Single & Dual Output Miniature, 2W SIP DC/DC Converters
D200 Series
Single & Dual Output
Miniature, 2W SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• Miniature SIP Case
• Single & Dual Outputs
• 1,000 VDC Isolation
• >1.12 MHour MTBF
• 28 Standard Models
• Industry Standard Pin-Out
Input
Parameter
Input Voltage Range
Input Filter
Reflected Ripple Current
Output
Conditions
Min. Typ.
5 VDC Input 4.5 5.0
12 VDC Input 10.8 12.0
24 VDC Input 21.6 24.0
48 VDC Input 43.2 48.0
Internal Capacitor
12 µH Source Inductance
20
Max.
5.5
13.2
26.4
52.8
Units
VDC
mA P - P
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±3.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0
%
Line Regulation
Load Regulation
For Vin Change of 1%
±1.2
%
See Model Selection Guide
Ripple & Noise (20 MHz)
75
mV P - P
Output Power Protection
120
%
Temperature Coefficient
±0.02 %/ºC
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
Isolation Resistance
60 Seconds 1,000
500 VDC 1,000
VDC
M⍀
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
80
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case
+100
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)
0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Weight
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
0.08 Oz (2.3g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 1.12
Units
MHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max.
5 VDC Input -0.7
7.0
12 VDC Input -0.7
15.0
24 VDC Input -0.7
28.0
Units
VDC
48 VDC Input -0.7
54.0
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec
All Models
260
ºC
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com