|
URA2405LD-20WR3_15 Datasheet, PDF (2/9 Pages) MORNSUN Science& Technology Ltd. – DC/DC Converter | |||
|
◁ |
DC/DC Converter
URA_LD-20WR3 & URB_LD-20WR3 Series
Input Specifications
Item
Operating Conditions
Min.
Typ.
Max.
Unit
24VDC input
3.3V output
5V output
--
799/40
818/45
--
969/40
993/45
Input Current (full load / no-load)
48VDC input
Others
3.3V output
5V output
--
948/6
941/10
--
400/20
409/25
mA
--
485/20
497/25
Others
--
474/5
485/9
Reflected Ripple Current
24VDC input
48VDC input
--
30
--
--
30
--
Input impulse Voltage (1sec. max.)
24VDC input
48VDC input
-0.7
--
50
-0.7
--
100
Starting Voltage
24VDC input
48VDC input
--
--
9
VDC
--
--
18
Under Voltage Shutdown
24VDC input
48VDC input
5.5
6.5
--
14.0
15.5
--
Starting Time
Input Filter
Nominal input& constant resistance load
--
10
--
ms
Pi filter
Module switch on
Ctrl suspended or connected to TTL high level (3.5-12VDC)
Ctrl*
Module switch off
Ctrl pin connected to GND or low level (0-1.2VDC)
Input current when switched off
--
4
7
mA
Hot Plug
Note: *The voltage of Ctrl pin is relative to input pin GND.
Unavailable
Output Specifications
Item
Output Voltage Accuracyâ
Balance of Output Voltage
Line Regulation
Load Regulationâ¡
Cross Regulation
Transient Recovery Time
Transient Response Deviation
Temperature Drift Coefficient
Ripple & Noiseâ¢
Trim
Over-voltage Protection
Over-current Protection
Short circuit Protection
Operating Conditions
0%-100% load
Dual output, balanced load
Full load, the input voltage is
Positive Output
from low voltage to high voltage Negative Output
5%-100% load
Positive Output
Negative Output
Dual output, main output 50% load,
Supplement output from 10% to 100% load
25% load step change 3.3V/5V/±5V output
Others
Full load
20MHz bandwidth, 5%-100% load
Input voltage range
Min.
Typ.
Max.
Unit
--
±1
±3
--
±0.5
±1.5
--
±0.2
±0.5
--
±0.5
±1
%
--
±0.5
±1
--
±0.5
±1.5
--
--
±5
--
300
500
µs
--
±5
±8
%
--
±3
±5
--
--
±0.03
%/â
--
50
100
Mv p-p
--
±10
--
110
--
160
%Vo
110
--
190
%Io
Hiccup, Continuous, self-recovery
Note:â At 0%~5% load, the Max. output voltage accuracy of ±5VDC/±9VDC output converter is ±5%.
â¡When testing from 0% to100%load working conditionsï¼load regulation index of ±5%ï¼
â¢0%-5% load ripple&Noise is no more than 5%Vo.Ripple and noise are measured by âparallel cableâ method, please see DC-DC Converter Application
Notes for specific operation.
2015.09.28-A/3
Page 2 of 9
MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation
|
▷ |