63811-6000 Datasheet, PDF (2/5 Pages) Molex Electronics Ltd. – Hand Crimp Tool Specification Sheet

Hand Crimp Tool for 1.50mm (.591") Pitch, MX150 Crimp Terminals
CRIMP SPECIFICATION
Terminal Series No.
Bell mouth
mm
In.
Conductor Brush
mm
In.
33001
0.25-1.25 .010-.049 0.15-0.40 .006-.016
33012
0.25-1.25 .010-.049 0.15-0.40 .006-.016
34750
0.25-1.25 .010-.049 0.15-0.40 .006-.016
Wire brush to be below top of conductor crimp.
Terminal
Series No.
33001
33012
34750
Bend up Bend down
Twist Roll
Degree
Degree
Crimped terminals and up to 5mm of wire past the insulator
cutoff tab must freely fit in the Checking Aid, Part No. 63868-2008
Seam
Seam shall not be
open and no wire allowed
out of the crimping area
Order Separately
After crimping, the crimp profiles should measure the following:
Terminal Series No.
33001
33012
34750
Wire Size
AWG mm²
18 0.83
20 0.58
22 0.36
18 0.83
20 0.58
22 0.36
18 0.83
20 0.58
22 0.36
Conductor
Crimp Height
Crimp Width
mm
In.
mm
In.
1.20-1.30 .047-.051 2.05-2.25 .081-.089
1.10-1.20 .043-.047 2.05-2.25 .081-.089
0.95-1.05 .037-.041 1.50-1.70 .059-.067
1.20-1.30 .047-.051 2.05-2.25 .081-.089
1.10-1.20 .043-.047 2.05-2.25 .081-.089
0.95-1.05 .037-.041 1.50-1.70 .059-.067
1.20-1.30 .047-.051 2.05-2.25 .081-.089
1.10-1.20 .043-.047 2.05-2.25 .081-.089
0.95-1.05 .037-.041 1.50-1.70 .059-.067
Profile
AWG
18 20 22
X
X
X
X
X
X
X
X
X
Terminal Series No.
33001
33012
34750
Wire Size
AWG mm²
18 0.83
20 0.58
22 0.36
18 0.83
20 0.58
22 0.36
18 0.83
20 0.58
22 0.36
Insulation
Crimp Height
Crimp Width
mm
In.
mm
In.
1.90-2.10 .075-.083 2.20-2.40 .086-.094
1.80-2.00 .071-.079 2.00-2.20 .079-.087
1.75-1.95 .069-.077 1.80-2.00 .071-.079
1.90-2.10 .075-.083 2.20-2.40 .086-.094
1.80-2.00 .071-.079 2.00-2.20 .079-.087
1.75-1.95 .069-.077 1.80-2.00 .071-.079
1.90-2.10 .075-.083 2.20-2.40 .086-.094
1.80-2.00 .071-.079 2.00-2.20 .079-.087
1.75-1.95 .069-.077 1.80-2.00 .071-.079
Pull Force
Minimum
N Lb.
89.9 20.2
75.6 17.0
49.8 11.2
89.9 20.2
75.6 17.0
49.8 11.2
89.9 20.2
75.6 17.0
49.8 11.2
Τ Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Doc No: ATS-638116000
Revision: E
Release Date: 03-21-06
Revision Date: 10-01-09
UNCONTROLLED COPY
Page 2 of 5