M37754M8C-XXXGP Datasheet, PDF (81/114 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16BIT CMOS MICROCOMPUTER

PRELIMINARY _{NSootimcee: pTahriasmisentroict} ^{alimfinitsalasrpeescuifbicjeactitotno. change.}
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS (Vcc = 5 V, Vss = 0 V, Ta = –20 to 85 °C, f(XIN) = 40 MHz (Note))
Symbol
Parameter
Test conditions
Limits
Min. ^{Typ. Max. Unit}
High-level output voltage P00–P07, P10–P17, P20–P23,
P27, P31, P33, P40–P47,
VOH
P50–P57, P60–P67, P70–P77, IOH = –10 mA
P80–P87, P90–P92, P95,
P100–P107, P110–P117
3.4
V
VOH
VOH
High-level output voltage P00–P07, P10–P17, P20–P23,
P27, P31, P33, P90–P92,
P100–P107, P110–P117
_
High-level output voltage E, P30, P32
IOH = –400 µA
IOH = –10 mA
IOH = –400 µA
4.8
V
3.4
4.8
V
High-level output voltage P93, P94
VOH
IOH = –15 mA
IOH = –600 µA
3.4
4.8
V
Low-level output voltage P00–P07, P10–P17, P20–P23,
P27, P31, P33, P40–P47,
VOL
P54–P57, P60–P67,P70–P77, _{IOL = 10 mA}
P80–P87, P90, P95,
P100–P107, P110–P117
2
V
Low-level output voltage P00–P07, P10–P17, P20–P23,
VOL
P27, P31, P33, P90,
IOL = 2 mA
P100–P107, P110–P117
_
Low-level output voltage E, P30, P32
VOL
IOL = 10 mA
IOL = 2 mA
0.45
V
1.6
0.4
V
VOL
VT+ —VT–
VT+ —VT–
Low-level output voltage P50–P53, P91–P94
Hysteresis
Hysteresis
_____ ____
HOLD, RDY, T_A_0_IN_–_T_A_4_IN,_____
T_{_}B_{__} 0_{_} IN–_{_} T_{_}B_{_}2_{_}IN, INT0–INT4, ADTRG,
CTS0, CTS1, CLK0, CLK1, RxD0,
RxD1
______ _____ ____
RESET, HOLD, RDY
IOL = 20 mA
IOL = 2 mA
2
V
0.4
0.4
1
V
0.2
0.5
V
VT+ —VT– Hysteresis XIN
0.1
0.3
V
High-level input current P00–P07, P10–P17, P20–P23,
P27, P30–P33, P40–P47,
IIH
P50–P57, P60–P67, P70–P77,
P80–P87, P90–P95,
VI = 5 V
P100–P107, P110–P117, XIN,
RESET, CNVSS, BYTE
5
µA
Low-level input current P00–P07, P10–P17, P20–P23,
P27, P30–P33, P40–P47,
P50–P53, P60–P67, P70–P77,
IIL
P80–P87, P90–P95,
VI = 0 V
P100–P107, P110–P117, XIN,
RESET, CNVSS, BYTE
–5
µA
IIL
Low-level input current P54–P57, P95
VI = 0 V, No pull-up transistor
–5
µA
VI = 0 V, Pull-up transistor used
–0.25 –0.5 –1.0 mA
VRAM
ICC
RAM hold voltage
Power supply current (target value)
When clock is stoped.
2
Output-only pin is
open and other
f(XIN) = 40 MHz, square
waveform (Note)
pins are Vss during Ta = 25 °C when clcock
reset.
is stopped.
Ta = 85 °C when clcock
is stopped.
V
25
50 mA
1
µA
20
Note: f(XIN) = 20 MHz when the clock source select bit = “1.”
81