PDSP16350_96 Datasheet, PDF (10/12 Pages) Mitel Networks Corporation – I/Q Splitter/NCO

PDSP16350
ABSOLUTE MAXIMUM RATINGS (Note 1)
Supply voltage Vcc
-0.5V to 7.0V
Input voltage V_IN
-0.5V to Vcc + 0.5V
Output voltage V_OUT
-0.5V to Vcc + 0.5V
Clamp diode current per pin I_K (see note 2)
18mA
Static discharge voltage (HMB)
500V
Storage temperature T_S
-65°C to 150°C
Ambient temperature with power applied T_AMB
Military
-55°C to +125°C
Industrial
-40°C to 85°C
Junction temperature
150°C
Package power dissipation
3500mW
Thermal resistances
Junction to Case ø_JC
5°C/W
NOTES
1. Exceeding these ratings may cause permanent damage.
Functional operation under these conditions is not implied.
2. Maximum dissipation or 1 second should not be ex-
ceeded, only one output to be tested at any one time.
3. Exposure to absolute maximum ratings for extended peri-
ods may affect device reliablity.
4. Vcc = Max, Outputs Unloaded, Clock Freq = Max.
5. CMOS levels are defined as
VIH = VDD - 0.5v
VIL = +0.5v
6. Current is defined as positive into the device.
7. The ø_JC data assumes that heat is extracted from the top
face of the package.
ELECTRICAL CHARACTERISTICS
Operating Conditions (unless otherwise stated)
Commercial: T_AMB = 0°C to +70°C T_J(MAX) = 95°C V_CC = 5.0V±5% Ground = 0V
Industrial: T_AMB = -40°C to +85°C T_J(MAX) = 110°C V_CC = 5.0V±10% Ground = 0V
Military: T_AMB = -55°C to +125°C T_J(MAX) = 150°C V_CC = 5.0V±10% Ground = 0V
Static Characteristics
Characteristic
Output high voltage
Output low voltage
Input high voltage
Input low voltage
Input leakage current
Input capacitance
Output leakage current
Output S/C current
Symbol
V_OH
V_OL
V_IH
V_IL
I_IN
C_IN
I_OZ
I_SC
Value
Min. Typ. Max.
2.4
-
-
0.4
3.0
-
-
0.8
-10
+10
10
-50
+50
40
250
Units Conditions
V
I_OH = 4mA
V
I_OL = -4mA
V
V
µA
GND < V_IN < V_CC
pF
µA
GND < V_OUT < V_CC
mA V = Max
CC
Switching Characteristics
Characteristic
D33:0 signal setup to clock rising edge
D33:0 signal hold after clock rising edge
CEN setup to clock rising edge
CEN hold after clock rising edge
JUMP, RES setup to clock rising edge
JUMP hold after clock rising edge
RES hold after clock rising edge
Clock rising edge to output valid
Clock freq
Clock High Time
Clock Low Time
OES,OEC low to data valid
OES,OEC high to data high impedance
Pipeline delay VIN to VOUT
Vcc Current (CMOS inputs)
Vcc Current (TTL inputs)
Industrial
Min.
15
4
20
0
10
6
8
5
DC
15
20
-
-
31
-
-
Typ.
Max.
-
-
-
-
-
-
-
30
20
-
-
20
20
31
430
460
Military
Units
Min.
15
4
20
0
10
6
8
5
DC
15
20
-
-
31
-
-
Typ.
Max.
- ns
- ns
- ns
- ns
- ns
- ns
- ns
30 ns
20 MHz
- ns
- ns
20 ns
20 ns
31 CLKs
450 mA
500 mA
Conditions
30pF
30pF
30pF
See Note 4
See Note 4
10