M1500 Datasheet, PDF (6/9 Pages) GSI Group, Inc. – Mercury TM1500 Digital Output Encoder Systems Factory Set Resolution to 0.50μm

Mechanical Information -
Sensor with Standard D-sub Connector
139..47 [[150000] oorr7389.7.4[2[010000]0o]r
o¹⁹r⁶7^.98.^[7⁵⁰[⁰2⁰0^]0^±0^.]⁵⁰±.^[5¹0^2.[⁷1^] 2.7]
2.05 52.0
.142 [3.61]
CABLE DIAMETER
.272 6.91
.166 4.22
A
SENSOR MTG SURFACE
.058 1.47
.083 2.11
B
.155 3.94
.334 8.5
.500 12.70
2X .106 2.69
THRU.
.810 20.57
.650 16.5
.13 3.4
.037 0.94
.405 10.29
.24 6.2
.345 8.75
.080 2.03
C
PIN 8
PIN 1
PIN 15
PIN 9
Mechanical Information -
Sensor with Micro-connector
.142 [3.61]
CABLE DIAMETER
.40 [10.2]
.32 8.1
.272 6.91
.166 4.22
A
SENSOR MTG SURFACE
.058 1.47
B
.083 2.11
.155 3.93
.334 8.5
.500 12.70
2X .106 2.69
THRU.
.810 20.57
.650 16.5
.25 6.4
HEX SHAPED
ALUMINUM SLEEVE
(MAX OD .20 [5.1])
.38 9.7
3₁9₉._.4₇[_[1₅0₀0₀0_]] o_or_r 7₃8₉._.7₄[2_[10₀0₀0]_0]or
1_o9_r6₇.9_8.[₇50_[0₂0₀]₀±_0].5_±0_.5[1₀2._[7₁]_2.7]
.13 3.4
A
1.66 [42.2]
.405 10.29
.24 6.2
.345 8.75
.080 2.03
C
PIN 9
KEYWAY
PIN 1
PIN 10
DETAIL A
SCALE: 3:1
PIN 2
.62 15.7
Mercury 1500S Outputs
15-pin Standard Male D-sub connector
PIN FUNCTION
1
Reserved - do not connect
2
Reserved - do not connect
3
Reserved - do not connect
4
A - quadrature
5
A + quadrature
6
Reserved - do not connect
7
Sine+***
8
Cosine+***
9
B- quadrature
10
B+ quadrature
11
Reserved - do not connect
12
+5VDC
13
Ground
14
Index Window+
15
Index Window-
*** Analog outputs are for sensor alignment only and
are nominally 0.85VPP with 1.7V offset.
Index Window
Pin 14 on M1500S and
pin 6 on M1500H
20µm Typical
5VDC
Mercury 1500H Outputs
Micro-connector (Female 5 x 2 Header)
PIN FUNCTION
1
Sine+***
2
Index Window -
3
Cosine+***
4
Ground
5
A + quadrature**
6
Index Window +
7
A - quadrature**
8
+5VDC
9
B+ quadrature**
10
B- quadrature**
**Compatible with RS-422 receiver
*** Analog outputs are for sensor alignment only
and are nominally 0.85VPP with 1.7V offset.
Note: See user manual for guidelines on
cable strain relief and grounding.
All Specifications are subject to change. All data is accurate to the best of our knowledge.
MicroE Systems is not responsible for errors.
Page 6 of 9