H-XVD Datasheet, PDF (2/2 Pages) Microdc power Technology Co., Ltd – 1W,FIXED INPUT,6000V ISOLATED&UNREGULATED SINGLE/DUAL OUTPUT DC-DC CONVERTER

OUTPUT SPECIFICATIONS
Item
Test conditions
Min
Typ
Max
Output power
0.1
1
Line regulation
For Vin change of 1%
±1.2
10% to 100% load 5V output
10
15
Load regulation
10% to 100% load 9V output
10% to 100% load 12V output
8.3
15
6.8
15
10% to 100% load 15V output
6.3
15
Output voltage accuracy
See tolerance envelope graph
Temperature drift
100% full load
0.03
Ripple & Noise*
20MHz Bandwidth
150
200
Full load
5V input
250
Switching frequency
nominal input
12V input
50
*Test ripple and noise by "parallel cable"method.
See detailed operation instructions at Testing of Power Converter section, application notes.
Note: Dual output models unbalanced load: ±5%.
TYPICAL CHARACTERISTICS
H-XVD&G-XVD Series
Units
W
Recommended testing and application circuit
If you want to further decrease the input/output ripple, an
“ LC ” filtering network may be connected to the input and output
ends of the DC/DC converter, see (Figure 1).
%
%/℃
mVp-p
KHz
It should also be noted that the inductance and the frequency of the
"LC" filtering network should be staggered with the DC/DC frequency to
avoid mutual interference. However, the capacitance of the output
filter capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output,
provided the safe and reliable operation is ensured, the greatest
capacitance of its filter capacitor sees (Table 1).
EXTERNAL CAPACITOR TABLE (Table 1)
Single
Dual
Vin
Cin
(VDC)
(uF)
Vout
Cout
(uF)
Vout
Cout
(uF)
(VDC)
(VDC)
5
4.7
5
10
±5
4.7
12
2.2
9
4.7
±9
2.2
24
1
12
2.2
±12
1
-
-
15
1
±15
1
It not recommend to connect any external capacitor in the
application field with less than 0.5 watt output.
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and
over-current protection is a linear voltage regulator with overheat
protection that is connected to the input or output end in series (Figure 2).
Dual Output
OUTLINE DIMENSIONS & PIN CONNECTIONS
Overload Protection
Under normal operating conditions, the output circuit of
these products has no protection against overload. The simplest
method is to connect a self-recovery fuse in series at the input
end or add a circuit breaker to the circuit.
No parallel connection or plug and play
Note:
1. All specifications measured at Ta=25, humidity<75%,nominal input
voltage and rated output load unless otherwise specified.
2. Only typical models listed, other models may be different,
please contact our technical person for more details.
3. Operation under minimum load will not damage the
converter; However, they may not meet all specification listed.
Microdc Professional Power Module,Inc.
Tel:[phone] E-mail:[e-mail]
Website:http://www.microdc.cn
Microdc Professional Power module,Inc.makes no representation that
the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or
future patent rights. Specifications are subject to change without notice.
2010 Microdc Professional Power Module, Inc. Guangzhou
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn Technical Enquiries-Email:[e-mail] Tel:[phone] Page 2 of 2