24FC128 Datasheet, PDF (3/26 Pages) Microchip Technology – 128K I2C CMOS Serial EEPROM

24AA128/24LC128/24FC128
TABLE 1-2: AC CHARACTERISTICS
AC CHARACTERISTICS
Electrical Characteristics:
Industrial (I):
VCC = +1.8V to 5.5V TA = -40°C to +85°C
Automotive (E): VCC = +2.5V to 5.5V TA = -40°C to 125°C
Param.
No.
Sym.
Characteristic
Min.
Max. Units
Conditions
1
FCLK Clock frequency
—
100
kHz 1.8V ≤ VCC < 2.5V
—
400
2.5V ≤ VCC ≤ 5.5V
—
400
1.8V ≤ VCC < 2.5V 24FC128
—
1000
2.5V ≤ VCC ≤ 5.5V 24FC128
2
THIGH Clock high time
4000
600
600
500
—
ns 1.8V ≤ VCC < 2.5V
—
2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V 24FC128
—
2.5V ≤ VCC ≤ 5.5V 24FC128
3
TLOW Clock low time
4700
1300
1300
500
—
ns 1.8V ≤ VCC < 2.5V
—
2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V 24FC128
—
2.5V ≤ VCC ≤ 5.5V 24FC128
4
TR
SDA and SCL rise time
(Note 1)
—
1000
ns 1.8V ≤ VCC < 2.5V
—
300
2.5V ≤ VCC ≤ 5.5V
—
300
1.8V ≤ VCC ≤ 5.5V 24FC128
5
TF
SDA and SCL fall time
(Note 1)
—
300
ns All except, 24FC128
—
100
1.8V ≤ VCC ≤ 5.5V 24FC128
6
THD:ST Start condition hold time
A
4000
600
600
250
—
ns 1.8V ≤ VCC < 2.5V
—
2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V 24FC128
—
2.5V ≤ VCC ≤ 5.5V 24FC128
7
TSU:ST Start condition setup time
4700
A
600
600
250
—
ns 1.8V ≤ VCC < 2.5V
—
2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V 24FC128
—
2.5V ≤ VCC ≤ 5.5V 24FC128
8
THD:DA Data input hold time
T
0
—
ns (Note 2)
9
TSU:DA Data input setup time
T
250
—
ns 1.8V ≤ VCC < 2.5V
100
—
2.5V ≤ VCC ≤ 5.5V
100
—
1.8V ≤ VCC ≤ 5.5V 24FC128
10
TSU:ST Stop condition setup time
O
4000
600
600
250
—
ns 1.8 V ≤ VCC < 2.5V
—
2.5 V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V 24FC128
—
2.5 V ≤ VCC ≤ 5.5V 24FC128
11
TSU:WP WP setup time
4000
600
600
—
ns 1.8V ≤ VCC < 2.5V
—
2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC ≤ 5.5V 24FC128
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model, which can be obtained from Microchip’s web site:
www.microchip.com.
 2004 Microchip Technology Inc.
DS21191M-page 3