PIC18F1230 Datasheet, PDF (265/312 Pages) Microchip Technology – 18/20/28-Pin, Enhanced Flash Microcontrollers with nanoWatt Technology, High-Performance PWM and A/D

PIC18F1230/1330
22.2 DC Characteristics: Power-Down and Supply Current
PIC18F1230/1330 (Industrial)
PIC18LF1230/1330 (Industrial) (Continued)
PIC18LF1230/1330
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F1230/1330
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)⁽²⁾
PIC18LF1230/1330 0.8 TBD μA
-40°C
0.8 TBD μA
+25°C
VDD = 2.0V
0.8 TBD μA
+85°C
PIC18LF1230/1330 1.3 TBD mA
1.3 TBD mA
1.3 TBD mA
All devices 2.5 TBD mA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
INTOSC source)
2.5 TBD mA
2.5 TBD mA
+25°C
+85°C
VDD = 5.0V
Extended devices only 2.5 TBD mA
+125°C
PIC18LF1230/1330 2.9 TBD μA
-40°C
3.1 TBD μA
+25°C
VDD = 2.0V
3.6 TBD μA
+85°C
PIC18LF1230/1330 4.5 TBD μA
4.8 TBD μA
5.8 TBD μA
All devices 9.2 TBD μA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 31 kHz
(RC_IDLE mode,
INTRC source)
9.8 TBD μA
11.4 TBD μA
+25°C
+85°C
VDD = 5.0V
Extended devices only 21 TBD μA
+125°C
Legend:
Note 1:
2:
3:
4:
TBD = To Be Determined. Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS;
MCLR = VDD; WDT enabled/disabled as specified.
Low-power Timer1 oscillator selected.
BOR and LVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
© 2006 Microchip Technology Inc.
Advance Information
DS39758B-page 263