|
24LC1025-I-SM Datasheet, PDF (2/28 Pages) Microchip Technology – 1024K I2C™ Serial EEPROM | |||
|
◁ |
24AA1025/24LC1025/24FC1025
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(â )
VCC.............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS .......................................................................................................... -0.6V to VCC+1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied ................................................................................................-40°C to +125°C
ESD protection on all pins ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï®ï³ 4 kV
â NOTICE: Stresses above those listed under âAbsolute Maximum Ratingsâ may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 1-1: DC CHARACTERISTICS
DC CHARACTERISTICS
Industrial (I): VCC = +1.7V to 5.5V TA = -40°C to +85°C
Automotive (E): VCC = +2.5V to 5.5V TA = -40°C to +125°C
Param.
No.
Sym.
â
D1
VIH
D2
VIL
Characteristic
A1, A2, SCL, SDA and
WP pins:
High-level input voltage
Low-level input voltage
Min.
â
0.7 VCC
â
D3
VHYS Hysteresis of Schmitt
Trigger inputs
(SDA, SCL pins)
0.05 VCC
D4
VOL
Low-level output voltage
â
D5
ILI
Input leakage current
â
D6
ILO
Output leakage current
â
D7
CIN,
Pin capacitance
â
COUT (all inputs/outputs)
D8
ICC Read Operating current
â
ICC Write
â
D9
ICCS
Standby current
â
Max.
â
â
0.3 VCC
0.2 VCC
â
0.40
±1
±1
10
450
5
5
Units
â
Conditions
V
V VCC ï³ï 2.5V
V VCC < 2.5V
V VCC ï³ 2.5V (Note)
V IOL = 3.0 mA @ VCC = 4.5V
IOL = 2.1 mA @ VCC = 2.5V
ïA VIN = VSS or VCC
VIN = VSS or VCC
ïA VOUT = VSS or VCC
pF VCC = 5.0V (Note)
TA = 25°C, FCLK = 1 MHz
ïA VCC = 5.5V, SCL = 400 kHz
mA VCC = 5.5V
ïA SCL, SDA, VCC = 5.5V
A1, A2, WP = VSS
Note: This parameter is periodically sampled and not 100% tested.
DS21941K-page 2
ï£ 2005-2012 Microchip Technology Inc.
|
▷ |