PIC12F683 Datasheet, PDF (116/148 Pages) Microchip Technology – 8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology

PIC12F683
15.3 DC Characteristics: PIC12F683-E (Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +125°C for extended
Param
No.
Sym
Device
Characteristics
Min Typ† Max Units
VDD
Conditions
Note
D010E IDD
D011E
D012E
D013E
D014E
D015E
D016E
D017E
D018E
Supply Current^(1,2) —
9 TBD µA
— 18 TBD µA
— 35 TBD µA
— 110 TBD µA
— 190 TBD µA
— 330 TBD µA
— 220 TBD µA
— 370 TBD µA
— 0.6 TBD mA
— 70 TBD µA
— 140 TBD µA
— 260 TBD µA
— 180 TBD µA
— 320 TBD µA
— 580 TBD µA
— 10 TBD µA
— 25 TBD µA
— 40 TBD µA
— 340 TBD µA
— 500 TBD µA
— 0.8 TBD mA
— 250 TBD µA
— 375 TBD µA
— 750 TBD µA
— 3.0 TBD mA
— 3.7 TBD mA
2.0 FOSC = 32 kHz
3.0 ^{LP Oscillator mode}
5.0
2.0 FOSC = 1 MHz
3.0 ^{XT Oscillator mode}
5.0
2.0 FOSC = 4 MHz
3.0 ^{XT Oscillator mode}
5.0
2.0 FOSC = 1 MHz
3.0 ^{EC Oscillator mode}
5.0
2.0 FOSC = 4 MHz
3.0 ^{EC Oscillator mode}
5.0
2.0 FOSC = 31 kHz
3.0 ^{INTRC mode}
5.0
2.0 FOSC = 4 MHz
3.0 ^{INTOSC mode}
5.0
2.0 FOSC = 4 MHz
3.0 ^{EXTRC mode}
5.0
4.5 FOSC = 20 MHz
5.0 ^{HS Oscillator mode}
Legend:
†
Note 1:
2:
3:
4:
TBD = To Be Determined
Data in ‘Typ’ column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave,
from rail to rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O
pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have
an impact on the current consumption.
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this
peripheral is enabled. The peripheral ∆ current can be determined by subtracting the base IDD or IPD
current from this limit. Max values should be used when calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is
measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
DS41211B-page 114
Preliminary
 2004 Microchip Technology Inc.