|
DSPIC33FJ32MC204T-IPT Datasheet, PDF (1/330 Pages) Microchip Technology – 16-bit Digital Signal Controllers (up to 32 KB Flash and 2 KB SRAM) with Motor Control and Advanced Analog | |||
|
dsPIC33FJ32MC202/204 and
dsPIC33FJ16MC304
16-bit Digital Signal Controllers (up to 32 KB Flash and
2 KB SRAM) with Motor Control and Advanced Analog
Operating Conditions
⢠3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
⢠3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
Core: 16-bit dsPIC33F CPU
⢠Code-efficient (C and Assembly) architecture
⢠Two 40-bit wide accumulators
⢠Single-cycle (MAC/MPY) with dual data fetch
⢠Single-cycle mixed-sign MUL plus hardware divide
Clock Management
⢠2% internal oscillator
⢠Programmable PLLs and oscillator clock sources
⢠Fail-Safe Clock Monitor (FSCM)
⢠Independent Watchdog Timer (WDT)
⢠Fast wake-up and start-up
Power Management
⢠Low-power management modes (Sleep, Idle, Doze)
⢠Integrated Power-on Reset and Brown-out Reset
⢠1.35 mA/MHz dynamic current (typical)
⢠55 μA IPD current (typical)
High-Speed PWM
⢠Up to four PWM pairs with independent timing
⢠Dead time for rising and falling edges
⢠12.5 ns PWM resolution
⢠PWM support for:
- DC/DC, AC/DC, Inverters, PFC, Lighting
- BLDC, PMSM, ACIM, SRM
⢠Programmable Fault inputs
⢠Flexible trigger configurations for ADC conversions
Advanced Analog Features
⢠ADC module:
- Configurable as 10-bit, 1.1 Msps with four
S&H or 12-bit, 500 ksps with one S&H
⢠Six analog inputs on 28-pin devices and up to
nine analog inputs on 44-pin devices
⢠Flexible and independent ADC trigger sources
Timers/Output Compare/Input Capture
⢠Three 16-bit timers/counters. Can pair up two to
make one 32-bit.
⢠Two Output Capture modules configurable as
timers/counters
⢠Four Input Capture modules
⢠Peripheral Pin Select (PPS) to allow function
remap
Communication Interfaces
⢠One UART module (10 Mbps)
⢠With support for LIN 2.0 protocols and IrDA®
⢠One 4-wire SPI module (15 Mbps)
⢠One I2C⢠module (up to 1 Mbaud) with SMBus
support
⢠PPS to allow function remap
Input/Output
⢠Sink/Source up to 10 mA (pin specific) for stan-
dard VOH/VOL, up to 16 mA (pin specific) for
non-standard VOH1
⢠5V-tolerant pins
⢠Selectable open drain, pull-ups, and pull-downs
⢠Up to 5 mA overvoltage clamp current
⢠External interrupts on all I/O pins
Qualification and Class B Support
⢠AEC-Q100 REVG (Grade 0 -40ºC to +150ºC)
⢠Class B Safety Library, IEC 60730
Debugger Development Support
⢠In-circuit and in-application programming
⢠Two program and two complex data breakpoints
⢠IEEE 1149.2-compatible (JTAG) boundary scan
⢠Trace and run-time watch
Packages
Type
SPDIP
SOIC
Pin Count
28
28
Contact Lead/Pitch
.100''
1.27
I/O Pins
21
21
Dimensions
1.365x.285x.135'' 17.9xx7.50x2.05
Note: All dimensions are in millimeters (mm) unless specified.
SSOP
28
0.65
21
10.2x5.3x1.75
QFN-S
28
0.65
21
6x6x0.9
QFN
44
0.65
35
8x8x0.9
TQFP
44
0.80
35
10x10x1
© 2007-2012 Microchip Technology Inc.
DS70283K-page 1
|
▷ |