|
SY10EP16V_06 Datasheet, PDF (3/6 Pages) Micrel Semiconductor – 5V/3.3V HIGH-SPEED DIFFERENTIAL RECEIVER | |||
|
◁ |
Micrel, Inc.
ABSOLUTE MAXIMUM RATINGS(1)
ECL Proâ¢
SY10EP16V
Symbol
Rating
Value
Unit
VEE
VCC
VIN
IOUT
Power Supply Voltage (VCC = 0)
â6.0 to 0
Vdc
Power Supply Voltage (VEE = 0)
+6.0 to 0
Vdc
Input Voltage (VCC = 0V, VIN not more negative than VEE)
â6.0 to 0
Vdc
Input Voltage (VEE = 0V, VIN not more negative than VCC)
+6.0 to 0
Vdc
Output Current
âContinuous
âSurge
50
mA
100
IBB
TLEAD
TA
Tstore
VBB Sink/Source Current(2)
Lead Temperature (soldering, 20sec.)
Operating Temperature Range
Storage Temperature Range
±0.5
mA
+260
°C
â40 to +85
°C
â65 to +150
°C
Note :
1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied
at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended
periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS(1)
VCC = 0V; VEE = â5.5V to â3.0V; VCC = 3.0V to 5.5V, VEE = 0V(5)
Symbol
Parameter
TA = â40°C
Min.
Max.
Min.
TA = +25°C
Typ.
Max.
TA = +85°C
Min.
Max. Unit
IEE
Power Supply Current(2)
â
42
â
â
42
â
42
mA
VOH
Output HIGH Voltage(3)
VCC â1080 VCC â0890 VCC â0980
â
VCC â0810 VCC â0910 VCC â0720 mV
VOL
Outuput LOW Voltage(3)
VCC â1950 VCC â1650 VCC â1950
â
VCC â1630 VCC â1950 VCC â1595 mV
VIH
Input HIGH Voltage
VCC â1230 VCC â0890 VCC â1130
â
VCC â0810 VCC â1060 VCC â0720 mV
VIL
Input LOW Voltage
VCC â1950 VCC â1500 VCC â1950
â
VCC â1480 VCC â1950 VCC â1445 mV
VBB
Output Reference Voltage VCC â1430 VCC â1300 VCC â1350
â
VCC â1250 VCC â1310 VCC â1190 mV
VIHCMR Input HIGH Voltage
VEE +2.0 VCC â0.4 VEE +2.0
â
VCC â0.4 VEE +2.0 VCC â0.4 V
Common Mode Range(4)
IIH
Input HIGH Current
IIL
Input LOW Current
â
150
â
â
150
â
150
µA
0.5
â
0.5
â
â
0.5
â
µA
Notes:
1. 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a
test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained.
2. VCC = 0V, VEE = VEE(min.) to VEE(max.), all other pins floating.
3. All loading with 50⦠to VCC â 2.0V.
4. VIHCMR(min.) varies 1:1 with VEE, Max. varies 1:1 with VCC.
5. Input and output parameters vary 1:1 with VCC.
M9999-112805
hbwhelp@micrel.com or (408) 955-1690
3
|
▷ |