MIC2589_05 Datasheet, PDF (16/29 Pages) Micrel Semiconductor – Single-Channel, Negative High-Voltage Hot Swap Power Controller/Sequencer

Micrel
MIC2589/MIC2595
Functional Description
Hot Swap Insertion
When circuit boards are inserted into systems carrying
live supply voltages (“hot swapped”), high inrush
currents often result due to the charging of bulk
capacitance that resides across the circuit board’s
supply pins. These current spikes can cause the
system’s supply voltages to temporarily go out of
regulation causing data loss or system lock-up. In
more extreme cases, the transients occurring during a
hot swap event may cause permanent damage to
connectors or onboard components.
The MIC2589 and the MIC2595 are designed to
address these issues by limiting the maximum current
that is allowed to flow during hot swap events. This is
achieved by implementing a constant-current loop at
turn-on. In addition to inrush current control, the
MIC2589 and the MIC2595 incorporate input voltage
supervisory functions and user programmable
overcurrent protection, thereby providing robust
protection for both the system and the circuit board.
GATE Start-Up and Control
When the input voltage to the controller is between
the overvoltage and undervoltage threshold settings
(MIC2589) or is greater than the ON threshold setting
(MIC2595), a start cycle is initiated to deliver power to
the load. During the start-up cycle, the GATE pin of
the controller applies a constant charging current
(45µA, nominal) to the gate of the external MOSFET,
charging the MOSFET gate from 0V to 10V,
referenced to V_EE. An external capacitor (C2) can be
used to adjust and control the slew rate of the GATE
output, while resistor R4 can be used to minimize the
potential for parasitic high-frequency oscillations
occurring on the gate of the external MOSFET (M1).
See Typical Application circuit. The following
equation is used to approximate the expected inrush
current given the values of the capacitance at the gate
and the load (i.e., the gate of the external MOSFET
and the drain of the external MOSFET, respectively).
INRUSH =
C _LOAD
C_GATE
× I_GATE(ON)
Active current limiting for the MIC2589/MIC2595 is
implemented by controlling the voltage on the GATE
pin via an internal feedback circuit. The
MIC2589/MIC2595 is defined to be in current limit
when the GATE output voltage level is between 2.5V
and 5.5V. Once in current limit, the GATE output
voltage is regulated to limit the load current to the
programmed value (I_LIMIT).
Additionally, the
December 2005
overcurrent delay and the no-load detection timers
must be set accordingly to allow the output load to
fully charge during the start-up cycle. See the “Circuit
Breaker Function” and “No-Load Detection” sections
for further details.
Resistor R4, in series with the power MOSFET’s gate,
may be required in some layouts to minimize the
potential for parasitic oscillations occurring in M1.
Note that resistance in this device of the circuit has a
slight
destabilizing
effect
upon
the
MIC2589/MIC2595’s current regulation loop. If
possible, use high-frequency PCB layout techniques
and use a dummy resistor (R4 = 0Ω) for the initial
evaluation. If during prototyping an R4 is required,
common values for R4 range between 4.7Ω to 20Ω for
various power MOSFETs.
Circuit Breaker Function
The MIC2589 and MIC2595 device family employs an
electronic circuit breaker that protects the external
power MOSFET and other system components
against large-scale faults, such as short circuits. The
current-limit threshold is set via an external resistor,
R_SENSE, connected between the VEE and SENSE pins.
I_LIMIT
=
V_TRIP
R _SENSE
An overcurrent filter period is set via a capacitor from
the CFILTER pin to ground (C_FILTER) that determines
the length of the time period (t_FLT) for which the device
remains in current limit before the circuit breaker is
tripped. This programmable delay prevents tripping of
the circuit breaker due to the large inrush current
charging bulk and distributed capacitive loads.
Whenever the voltage across R_SENSE exceeds 50mV,
two things happen:
1. A constant-current regulation loop is engaged
which is designed to hold the voltage across
R_SENSE equal to 50mV. This protects both the
load and the MIC2589/MIC2595 circuits from
excessively high currents. This current-
regulation loop will engage in less than 1µs
from the time at which the overcurrent trip
threshold on R_SENSE is exceeded.
2. Capacitor C_FILTER is charged up to an internal
V_{CFILTER(TRIP)} threshold of 1.25V by
I_{CFILTER(CHARGE)} an internal 95µA current
source. If the voltage across CFILTER
crosses this threshold, the circuit breaker trips
and the GATE pin is immediately pulled low
by an internal current pull-down. This
operation turns off the MOSFET quickly and
disconnects the input from the load. The time
period that allows for the output to regulate in
16
M9999-120505
[phone]