MAX14589E Datasheet, PDF (4/11 Pages) Maxim Integrated Products – High-Density, ±5V Capable DPDT Analog Switches

MAX14589E/MAX14594E
High-Density, ±5V Capable DPDT Analog Switches
ELECTRICAL CHARACTERISTICS (continued)
(V_CC = +1.6V to +5.5V, T_A = -40NC to +85NC, unless otherwise noted. Typical values are at V_CC = +2.5V and T_A = +25NC.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
COM_ On-Leakage Current
DYNAMIC TIMING
I_{COM_(ON)}
V_CCEN = 2.5V; switch closed;
V_{COM_} = +5.5V, -5.5V;
V_{NO_} or V_{NC_} = +5.5V, -5.5V, unconnected
-400
+400
nA
Turn-On Time
Turn-Off Time
Break-Before-Make Time
t_ON
t_OFF
t_BBM
V_{NO_}or V_{NC_} = 0V, R_L = 50I, Figure 1a
V_{NO_}or V_{NC_} = 0V, R_L = 50I, Figure 1a
R_L = 50I, V_CCEN = 3.3V, time for both
NC_/NO_ switches are open during
transition, Figure 1b (Note 5)
5
10
ms
1
2.25
ms
0
5
10
ms
AUDIO PERFORMANCE
Total Harmonic Distortion
Plus Noise
THD+N
f = 20Hz to 20kHz, V_{COM_} = 0.5V_P-P,
R_S = R_L = 50I, DC bias = 0V
0.001
%
Off-Isolation
R_S = R_L = 50I, V_{COM_} = 0.5V_P-P,
V_ISO
f = 100kHz, V_CCEN = 0V, DC bias = 0.25V,
-60
dB
Figure 2
Crosstalk
V_CT
R_S = R_L = 50I, V_{COM_} = 0.5V_P-P,
f = 100kHz, Figure 2 (Note 7)
-80
dB
-3dB Bandwidth
NC_ or NO_ Off-Capacitance
COM_ On-Capacitance
DIGITAL I/O (CB)
BW
C_{NC_(OFF)}
C_{NO_(OFF)}
C_{COM_(ON)}
R_S = R_L = 50I, Figure 2
V_{NC_/NO_} = 0.5V_P-P, f = 1MHz
V_{NC_/NO_} = 0.5V_P-P, f = 1MHz
200
MHz
25
pF
50
pF
Input Logic-High Voltage
Input Logic-Low Voltage
Input Leakage Current
ESD PROTECTION
V_IH
V_IL
I_IN
V_CB = 0V or V_CCEN
1.4
V
0.4
V
-1
+1
FA
Human Body Model
Q15
COM1, COM2
IEC 61000-4-2 Air-Gap Discharge
Q10
kV
IEC 61000-4-2 Contact Discharge
Q8
NO_, NC_
Human Body Model
Q15
kV
All Other Pins
Human Body Model
Q2
kV
Note 2: All specifications are 100% production tested at T_A = +25NC, unless otherwise noted. Specifications are over -40NC to
+85NC and are guaranteed by design.
Note 3: The same limits apply for V_{COM_} = -5.5V to +5.5V and are guaranteed by design.
Note 4: DR_ON(MAX) = |R_ON(CH1) - R_ON(CH2)|.
Note 5: Guaranteed by design; not production tested.
Note 6: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over
specified analog signal ranges.
Note 7: Between two switches.
  4