DSTINIS400 Datasheet, PDF (2/11 Pages) Maxim Integrated Products – Sockets Evaluation Board

COMPONENT LIST (continued)
DESIGNATION
C16, C18
C20–C22
C23, C24
D1
D2
J1
J2
J7
J9–J11
J12
J13
J14
J16
L1
R1
R2
R4–R7, R8,
R10–R12
R13, R9
R14
R15, R17, R18
R16
R19
QTY
2
3
2
1
1
1
1
1
3
1
1
1
1
1
1
1
DESCRIPTION
270pF capacitor (1206)
1nF, 2kV thru-hole
capacitors
27pF capacitors (1206)
1N5908 D0-201
BAT54 SOT-23
SODIMM144
Hirose SX6E-144S-0.8SH
2.5mm center, 5.5mm
outside barrel connector
RJ-45 modular jack
3 x 1-pin headers, 0.1
centers
DB9 serial female
DB9 serial male
Pad jumper
RJ11 modular jack
22mH inductor
205kW, ±1% resistor (1206)
121kW, ±1% resistor (1206)
8 49.9W, ±1% resistors (1206)
2 47W resistor (1206)
1 22.1kW, ±1% resistor (1206)
3 220W resistors (1206)
1 10kW resistor (1206)
1 Pad jumper
JUMPERS (DSTINIS400)
Network Boot Jumper (J3)
JUMPER
CONFIGURATION
1–2
DS80C400 attempts to boot through
Ethernet using DHCP and TFTP
Quiet Boot Jumper (J5)
JUMPER
CONFIGURATION
1–2
DS80C400 boots without sending loader
information to serial port.
Auto Negotiation Jumper (J9)
JUMPER
CONFIGURATION
1–2
Auto-negotiation disabled.
2–3
Auto-negotiation enabled.
DSTINIs400/DSTINIs-00x Sockets Evaluation Board
DESIGNATION QTY
DESCRIPTION
R20
1 47kW resistor (1206)
R21
1 124W, ±1% resistor (1206)
R22, R23
2 1kW resistor (1206)
R24
1 10kW resistor (1206)
T1
1
BelFuse S558-5999-T7
transformer
U1
1
MAX1692 PWM step-down
regulator
U3
1
Intel LXT972ALC Ethernet
PHY
U4–U6
3 Dialight 597-7741 LED
U7
1 MAX560CAI transceiver
U8
1
DS2480B serial 1-Wire line
driver
U9
1
DS9502 ESD protection
diode
Y1
1 25.000MHz, HC49
Z1–Z3
3
Ferrite Bead, Fair-Rite
2512067007Y3
UNPOPULATED COMPONENTS
J15
1 DS9094F iButton^® Clip
J18, J28–J30
1 Not used
U2
1
MAX1792EUA18 linear
regulator
U10
1
DS2408 1-Wire 8-channel
addressable switch
U12
1 Not used
10/100Mb Ethernet Jumper (J10)
JUMPER
CONFIGURATION
1–2
100Mb Ethernet operation.
2–3
10Mb Ethernet operation.
Full Duplex Jumper (J11)
JUMPER
CONFIGURATION
1–2
Ethernet is configured for full-duplex
operation.
2–3
Ethernet is configured for half-duplex
operation.
DTR Reset Jumper (J11)
JUMPER
CONFIGURATION
1–2
DTR reset is used for communication with
the DS80C400 loader application.
iButton is a registered trademark of Dallas Semiconductor.
2 of 11