DG401 Datasheet, PDF (2/8 Pages) Intersil Corporation – Monolithic CMOS Analog Switches

Improved, Dual, High-Speed Analog Switches
ABSOLUTE MAXIMUM RATINGS
Voltage Referenced to V-
V+ .......................................................................................44V
GND ...................................................................................25V
V_L .................................................(GND - 0.3V) to (V+ + 0.3V)
Digital Inputs, V_S, V_D (Note 1) .......(V- - 2V) to (V+ + 2V) or 20mA
(whichever occurs first)
Continuous Current (any terminal) ......................................30mA
Continuous Current, S or D .................................................20mA
Peak Current, S or D
(pulsed at 1ms, 10% duty cycle max) ..........................100mA
Continuous Power Dissipation (T_A = +70°C)
16-Pin Plastic DIP(derate 10.53mW/°C above +70°C)...842mW
16-Pin Narrow SO (derate 8.70mW/°C above +70°C) ...696mW
16-Pin CERDIP (derate 10.00mW/°C above 70°C) .......800mW
20-Pin LCC (derate 9.09mW/°C above +70°C) ............727mW
Operating Temperature Ranges
DG40_C_ .............................................................0°C to +70°C
DG40_D_ ..........................................................-40°C to +85°C
DG40_A_ ........................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on S, D or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum
current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = 15V, V- = -15V, V_L = +5V, GND = 0V, V_INH = +2.4V, V_INL = +0.8V, T_A = T_MIN to T_MAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
SWITCH
Analog Signal Range
Drain-Source
On-Resistance
V_ANALOG
r_DS(ON)
Drain-Source
On-Resistance Match
∆r_DS(ON)
Between Channels (Note 4)
(Note 3)
V+ = 13.5V, V- = -13.5V,
I_S = -10mA,
V_D = ±10V,
V_INH = 2.4V,
V_INL = 0.8V
V+ = 15V, V- = -15V,
I_S = -10mA,
V_D = ±10V
T_A = +25°C
T_A = T_MIN to T_MAX
T_A = +25°C
T_A = T_MIN to T_MAX
TEMP. MIN
RANGE
TYP
(Note 2)
MAX
UNITS
-15
+15 V
C,D
20
45
A
20
30
Ω
C,D
55
A
45
C, D, A
0.5
2
Ω
3
On-Resistance Flatness
(Note 4)
Source-Off
Leakage Current
(Note 7)
V+ = 15V, V- = -15V,
r_FLAT(ON) I_S = -10mA,
V_D = ±5V, 0V
T_A = +25°C
T_A = T_MIN to T_MAX
I_S(OFF)
V+ = 16.5V, V- = -16.5V, ^TA ^{= +25°C}
V_D = 15.5V,
V_S = ±15.5V,
T_A = T_MIN to T_MAX
Drain-Off
Leakage Current
(Note 7)
I_D(OFF)
V+ = 16.5V, V- = -16.5V, ^TA ^{= +25°C}
V_D = ±15.5V,
V_S = 15.5V
T_A = T_MIN to T_MAX
Drain-On
Leakage Current
(Note 7)
I_D(ON)
or
I_S(ON)
V+ = 16.5V, V- = -16.5V, ^TA ^{= +25°C}
V_D = ±15.5V,
V_S = ±15.5V
T_A = T_MIN to T_MAX
C, D, A
C, D
A
C, D
A
C, D
A
C, D
A
C, D
A
C, D
A
-0.50
-0.25
-5
-10
-0.50
-0.25
-5
-10
-1.0
-0.4
-10
-20
-0.01
-0.01
-0.01
-0.01
-0.04
-0.04
3
Ω
6
0.50
0.25
nA
5
10
0.50
0.25
nA
5
10
1.0
0.4
nA
10
20
2 _______________________________________________________________________________________