MAX1086 Datasheet, PDF (11/15 Pages) Maxim Integrated Products – 150ksps, 10-Bit, 2-Channel Single-Ended, and 1-Channel True-Differential ADCs in SOT23

150ksps, 10-Bit, 2-Channel Single-Ended, and
1-Channel True-Differential ADCs in SOT23
and is available in MSB-first format. Observe the
SCLK to DOUT valid timing characteristic. Clock
data into the µP on SCLK’s rising-edge.
SPI and MICROWIRE Interface
When using SPI interface (Figure 8a) or MICROWIRE
(Figure 8a and 8b), set CPOL = CPHA = 0. Two 8-bit
readings are necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the µP on
SCLK’s rising edge. The first 8-bit data stream contains
the first 8-bits of DOUT starting with the MSB. The sec-
ond 8-bit data stream contains the remaining two result
bits (B1, B0) and two trailing sub-bits (S1, S0). DOUT
then goes high impedance.
QSPI Interface
Using the high-speed QSPI interface (Figure 9a) with
CPOL = 0 and CPHA = 0, the MAX1086–MAX1089
support a maximum f_SCLK of 8MHz. One 8- to16-bit
reading is necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the µP on
SCLK’s rising edge. The first 10 bits are the data and
the next two bits are sub-bits (S1, S0). DOUT then
goes high impedance (Figure 9b).
PIC16 and SSP Module and
PIC17 Interface
The MAX1086–MAX1089 are compatible with a
PIC16/PIC17 microcontroller (µC), using the synchro-
nous serial port (SSP) module
To establish SPI communication, connect the controller
as shown in Figure 10a and configure the PIC16/PIC17
as system master. This is done by initializing its syn-
chronous serial port control register (SSPCON) and
synchronous serial port status register (SSPSTAT) to
the bit patterns shown in Tables 1 and 2.
In SPI mode, the PIC16/PIC17 µCs allow eight bits of
data to be synchronously transmitted and received
simultaneously. Two consecutive 8-bit readings (Figure
10b) are necessary to obtain the entire 10-bit result
from the ADC. DOUT data transitions on the serial
clock’s falling edge and is clocked into the µC on
SCLK’s rising edge. The first 8-bit data stream contains
I/O
SCK
MISO
V_DD
SPI
SS
CNVST
SCLK
DOUT
MAX1086–
MAX1089
I/O
SK
SI
MICROWIRE
CNVST
SCLK
DOUT
MAX1086–
MAX1089
Figure 8a. SPI Connections
Figure 8b. MICROWIRE Connections
Table 1. Detailed SSPCON Register Content
CONTROL BIT
WCOL
SSPOV
Bit 7
Bit 6
SSPEN
Bit 5
CKP
SSPM3
SSPM2
SSPM1
SSPM0
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
X = Don’t care
MAX1086–MAX1089
SETTINGS
SYNCHRONOUS SERIAL PORT CONTROL REGISTER (SSPCON)
X
Write Collision Detection Bit
X
Receive Overflow Detect Bit
Synchronous Serial Port Enable Bit.
1
0: Disables serial port and configures these pins as I/O port pins.
1: Enables serial port and configures SCK, SDO and SCI pins as serial port pins.
0
Clock Polarity Select Bit. CKP = 0 for SPI master mode selection.
0
0
Synchronous Serial Port Mode Select Bit. Sets SPI master mode and selects
0
f_CLK= f_OSC / 16.
1
______________________________________________________________________________________ 11