DS1500_11 Datasheet, PDF (11/20 Pages) Maxim Integrated Products – Y2K Watchdog RTC with Nonvolatile Control

DS1500 Y2KC Watchdog RTC with Nonvolatile Control
DETAILED DESCRIPTION
The RTC registers are double buffered into an internal and external set. The user has direct access to the external
set. Clock/calendar updates to the external set of registers can be disabled and enabled to allow the user to access
static data. When the crystal oscillator is turned on, the internal set of registers are continuously updated; this
occurs regardless of external register settings to guarantee that accurate RTC information is always maintained.
The DS1500 contains its own power-fail circuitry that automatically deselects the device when the V_CCI supply falls
below a power-fail trip point. This feature provides a high degree of data security during unpredictable system
operation caused by low V_CCI levels. An external SRAM can be made nonvolatile by using the V_CCO and CEO pins.
Nonvolatile control of the external SRAM is analogous to that of the RTC registers. When V_CCI slews down during a
power fail, CEO is driven to an inactive level regardless of CEI. This write protection occurs when V_CCI is less than
the power-fail trip point.
The DS1500 has interrupt (IRQ), power control (PWR), and reset (RST) outputs that can be used to control CPU
activity. The IRQ interrupt or RST outputs can be invoked as the result of a time-of-day alarm, CPU watchdog
alarm, or a kickstart signal. The DS1500 power-control circuitry allows the system to be powered on by an external
stimulus, such as a keyboard or by a time and date (wakeup) alarm. The PWR output pin can be triggered by one
or either of these events, and can be used to turn on an external power supply. The PWR pin is under software
control, so that when a task is complete, the system power can then be shut down. The DS1500 power-on reset
can be used to detect a system power-down or failure and hold the CPU in a safe reset state until normal power
returns and stabilizes; the RST output is used for this function.
The DS1500 is a clock/calendar chip with the features described above. An external crystal and battery are the
only components required to maintain time-of-day and memory status in the absence of power..
Table 1. RTC Operating Modes
VCCI
VCCI > VPF
VSO < VCCI < VPF
VCCI < VSO < VPF
CS
OE WE
V_IH
X
X
V_IL
X
V_IL
V_IL
V_IL
V_IH
V_IL
V_IH
V_IH
X
X
X
X
X
X
DQ0–DQ7
High-Z
D_IN
D_OUT
High-Z
High-Z
High-Z
A0–A4
X
A_IN
A_IN
A_IN
X
X
MODE
Deselect
Write
Read
Read
Deselect
Data Retention
POWER
Standby
Active
Active
Active
CMOS Standby
Battery Current
DATA READ MODE
The DS1500 is in read mode whenever CS (chip select) and OE (output enable) are low and WE (write enable) is
high. The device architecture allows ripple-through access to any valid address location. Valid data is available at
the DQ pins within t_AA (address access) after the last address input is stable, provided that CS and OE access
times are satisfied. If CS or OE access times are not met, valid data is available at the latter of chip-enable access
(t_CSA) or at output-enable access time (t_OEA). The state of the data input/output pins (DQ) is controlled by CS and
OE. If the outputs are activated before t_AA, the data lines are driven to an intermediate state until t_AA. If the address
inputs are changed while CS and OE remain valid, output data remains valid for output-data hold time (t_OH) but then
goes indeterminate until the next address access (Table 1).
DATA WRITE MODE
The DS1500 is in write mode whenever CS and WE are in their active state. The start of a write is referenced to the
latter occurring transition of CS or WE. The addresses must be held valid throughout the cycle. CS or WE must
return inactive for a minimum of t_WR prior to the initiation of a subsequent read or write cycle. Data in must be valid
t_DS prior to the end of the write and remain valid for t_DH afterward. In a typical application, the OE signal is high
during a write cycle. However, OE can be active provided that care is taken with the data bus to avoid bus
contention. If OE is low prior to a high-to-low transition on WE, the data bus can become active with read data
defined by the address inputs. A low transition on WE then disables the outputs t_WEZ after WE goes active (Table 1).
11 of 20