MAX1165EVKIT Datasheet, PDF (1/5 Pages) Maxim Integrated Products – MAX1165 Evaluation Kit

19-2558; Rev 0; 6/02
MAX1165 Evaluation Kit
General Description
The MAX1165 evaluation kit (EV kit) is an assembled
and tested circuit board that demonstrates the
MAX1165 analog-to-digital converter. The EV kit can
also evaluate the MAX1065/MAX1066 and MAX1165/
MAX1166. Request free samples of the desired parts
when ordering the MAX1165 EV kit.
o Proven PC Board Layout
o Convenient On-Board Test Points
o Fully Assembled and Tested
Features
Ordering Information
PART
MAX1165EVKIT
TEMP RANGE
0°C to +70°C
IC PACKAGE
28 TSSOP
Component List
Quick Start
DESIGNATION
C1, C2, C11,
C12
C3, C4, C5, C8,
C9, C10
C6
C7
C7, R2
H1
JU1–JU6
R1
R2
U1
U2
U3
None
None
None
QTY
DESCRIPTION
4
10µF, 10V X7R ceramic capacitors
Taiyo Yuden LMK325BJ106MN
6 0.1µF, 10V X7R ceramic capacitors
1 ^{4.7µF, 10V X7R ceramic capacitor}
Taiyo Yuden JMK212BJ475KG
1 0.01µF ceramic capacitor
4 Socket-pin receptacles
1 2 × 16 dual-row vertical header
6 2-pin headers
1 100kΩ ±5% resistor
1 4.7Ω ±5% resistor
1 MAX1165BEUI
1 Hex Schmitt trigger buffer 74HC14
1 MAX4430ESA
1 MAX1165 EV kit PC board
1 MAX1165 data sheet
1 MAX1165 EV kit data sheet
Component Supplier
SUPPLIER
Taiyo
Yuden
PHONE
FAX
WEBSITE
800-348-2496 847-925-0899 www.t-yuden.com
Note: Please indicate that you are using the MAX1165 when con-
tacting these component suppliers.
Recommended Equipment
• MAX1165 EV kit
• Two DC power supplies, 5V at 10mA
• Programmable signal generator, such as Tektronix
DG2020A
• Logic analyzer (optional)
• Reconstruction DAC (optional)
Procedure
The MAX1165 EV kit is fully assembled and tested.
Follow these steps to verify board operation. Do not turn
on the power supply until all connections are com-
pleted.
1) Ensure that JU1, JU2, and JU3 are open (see
Table 1).
2) With the power off, connect the first 5VDC power
supply between AVDD and AGND.
3) With the power off, connect the second 5VDC power
supply between DVDD and DGND. Note: DGND
and AGND are connected on the MAX1165 EV kit
board. To avoid ground loops, do not connect
AGND to DGND at any other location.
4) Configure the pattern generator to produce the
appropriate read/convert (R/C) and conversion start
(CS) waveforms. Refer to Figure 2 in the MAX1165
data sheet.
5) Connect the pattern generator CS output across
jumper JU4.
6) Connect the pattern generator R/C output across
jumper JU5.
7) Connect logic analyzer or other digital data capture
system to header H1. The least significant bit, D0,
appears on H1 pin 1, and the end-of-conversion out-
put strobe (EOC) appears across jumper JU6 (see
Table 2).
8) Turn on the power supplies and enable the pattern
generator.
9) Apply 0 to 4.096V analog input signal between
pads AIN and AGND. Capture digital data from
header H1.
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.