LTC3703_15 Datasheet, PDF (9/34 Pages) Linear Technology – 100V Synchronous Switching Regulator Controller

LTC3703
Operation (Refer to Functional Diagram)
drop in the feedback voltage relative to the reference. The
COMP voltage then rises, increasing the duty ratio until
the output feedback voltage again matches the reference
voltage. In normal operation, the top MOSFET is turned
on when the RS latch is set by the on-chip oscillator and
is turned off when the PWM comparator trips and resets
the latch. The PWM comparator trips at the proper duty
ratio by comparing the error amplifier output (after being
“compensated” by the line feedforward multiplier) to a
sawtooth waveform generated by the oscillator. When the
top MOSFET is turned off, the bottom MOSFET is turned
on until the next cycle begins or, if pulse-skip mode op-
eration is enabled, until the inductor current reverses as
determined by the reverse current comparator. MAX and
MIN comparators ensure that the output never exceed
±5% of nominal value by monitoring V_FB and forcing the
output back into regulation quickly by either keeping the top
MOSFET off or forcing maximum duty cycle. The operation
of its other features—fast transient response, outstanding
line regulation, strong gate drivers, short-circuit protection
and shutdown/soft-start—are described below.
Fast Transient Response
The LTC3703 uses a fast 25MHz op amp as an error ampli-
fier. This allows the compensation network to be optimized
for better load transient response. The high bandwidth of
the amplifier, along with high switching frequencies and
low value inductors, allow very high loop crossover fre-
quencies. The 800mV internal reference allows regulated
output voltages as low as 800mV without external level
shifting amplifiers.
Line Feedforward Compensation
The LTC3703 achieves outstanding line transient response
using a patented feedforward correction scheme. With
this circuit the duty cycle is adjusted instantaneously to
changes in input voltage, thereby avoiding unacceptable
overshoot or undershoot. It has the added advantage of
making the DC loop gain independent of input voltage.
Figure 2 shows how large transient steps at the input have
little effect on the output voltage.
V_OUT
50mV/DIV
V_IN
20V/DIV
I_L
2A/DIV
V_OUT = 12V
20µs/DIV
I_LOAD = 1A
25V TO 60V V_IN STEP
3703 F02
Figure 2. Line Transient Performance
Strong Gate Drivers
The LTC3703 contains very low impedance drivers capable
of supplying amps of current to slew large MOSFET gates
quickly. This minimizes transition losses and allows paral-
leling MOSFETs for higher current applications. A 100V
floating high side driver drives the topside MOSFET and
a low side driver drives the bottom side MOSFET (see
Figure 3). They can be powered from either a separate
DC supply or a voltage derived from the input or output
voltage (see MOSFET Driver Supplies section). The bottom
side driver is supplied directly from the DRV_CC pin. The
top MOSFET drivers are biased from floating bootstrap
capacitor, C_B, which normally is recharged during each off
cycle through an external diode from DRV_CC when the top
MOSFET turns off. In pulse-skip mode operation, where
it is possible that the bottom MOSFET will be off for an
extended period of time, an internal counter guarantees
that the bottom MOSFET is turned on at least once every
10 cycles for 10% of the period to refresh the bootstrap
capacitor. An undervoltage lockout keeps the LTC3703
shut down unless this voltage is above 8.7V.
The bottom driver has an additional feature that helps
minimize the possibility of external MOSFET shoot-through.
When the top MOSFET turns on, the switch node dV/dt
pulls up the bottom MOSFET’s internal gate through the
Miller capacitance, even when the bottom driver is holding
the gate terminal at ground. If the gate is pulled up high
enough, shoot-through between the topside and bottom
3703fc
9