LTC3261_15 Datasheet, PDF (8/14 Pages) Linear Technology – High Voltage, Low Quiescent Current Inverting Charge Pump

LTC3261
Applications Information
Effective Open-Loop Output Resistance
The effective open-loop output resistance (R_OL) of a charge
pump is a very important parameter which determines the
strength of the charge pump. The value of this parameter
depends on many factors such as the oscillator frequency
(f_OSC), value of the flying capacitor (C_FLY), the nonoverlap
time, the internal switch resistances (R_S) and the ESR of
the external capacitors.
Typical R_OL values as a function of temperature are shown
in Figure 2
60
V_IN = 32V
55
V_IN = 25V
V_IN = 12V
50
45
40
35
f_OSC = 500kHz
V_RIPPLE(P-P)
≈
I_OUT
C_OUT

•

1
f_OSC
–

t_ON


where f_OSC is the oscillator frequency t_ON is the on-time
of the oscillator (1µs) typical and C_OUT is the value of the
output capacitor.
Just as the value of C_OUT controls the amount of output
ripple, the value of C_IN controls the amount of ripple present
at the input (V_IN) pin. The amount of bypass capacitance
required at the input depends on the source impedance
driving V_IN. For best results it is recommended that V_IN
be bypassed with at least 2µF of low ESR capacitance. A
high ESR capacitor such as tantalum or aluminum will
have higher input noise than a low ESR ceramic capacitor.
Therefore, a ceramic capacitor is recommended as the
main bypass capacitance with a tantalum or aluminum
capacitor used in parallel if desired.
30
25
20
–50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
3261 F02
Figure 2. Typical R_OL vs Temperature
Input/Output Capacitor Selection
The style and value of capacitors used with the LTC3261
determine several important parameters such as regulator
control loop stability, output ripple, charge pump strength
and minimum turn-on time. To reduce noise and ripple, it is
recommended that low ESR ceramic capacitors be used for
the charge pump output. The charge pump output capacitor
should retain at least 2µF of capacitance over operating
temperature and bias voltage. Tantalum and aluminum
capacitors can be used in parallel with a ceramic capacitor
to increase the total capacitance but should not be used
alone because of their high ESR. In constant frequency
mode, the value of C_OUT directly controls the amount of
output ripple for a given load current. Increasing the size of
C_OUT will reduce the output ripple at the expense of higher
minimum turn-on time. The peak-to-peak output ripple at
the V_OUT pin is approximately given by the expression:
Flying Capacitor Selection
The flying capacitor controls the strength of the charge
pump. A 1µF or greater ceramic capacitor is suggested
for the flying capacitor for applications requiring the full
rated output current of the charge pump.
For very light load applications, the flying capacitor may
be reduced to save space or cost. For example, a 0.2µF
capacitor might be sufficient for load currents up to 20mA.
A smaller flying capacitor leads to a larger effective open-
loop resistance (R_OL) and thus limits the maximum load
current that can be delivered by the charge pump.
Ceramic Capacitors
Ceramic capacitors of different materials lose their capaci-
tance with higher temperature and voltage at different rates.
For example, a capacitor made of X5R or X7R material will
retain most of its capacitance from –40°C to 85°C whereas a
Z5U or Y5V style capacitor will lose considerable capacitance
over that range. Z5U and Y5V capacitors may also have a
poor voltage coefficient causing them to lose 60% or more of
their capacitance when the rated voltage is applied. Therefore
when comparing different capacitors, it is often more ap-
propriate to compare the amount of achievable capacitance
for a given case size rather than discussing the specified
capacitance value. The capacitor manufacture’s data sheet
3261fb
8
For more information www.linear.com/3261