RH1498M_15 Datasheet, PDF (4/8 Pages) Linear Technology – 10MHz, 6V/s, Dual Rail-to-Rail Input and Output Precision C-Load Op Amp

RH1498M
TABLE 2: ELECTRICAL CHARACTERISTICS
(Preirradiation) V_S = 5V; V_CM = V_OUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
Input Voltage Range
CONDITIONS
T_A = 25°C
SUB-
NOTES MIN TYP MAX GROUP
–55°C ≤ T_A ≤ 125°C
MIN TYP MAX
SUB-
GROUP
V^–
V⁺
V^– + 0.5V
V⁺ – 0.5V
UNITS
V
Input Noise Voltage
0.1Hz to 10Hz
400
e_n
Input Noise Voltage Density f = 1kHz
12
i_n
Input Noise Current Density f = 1kHz
0.3
C_IN
Input Capacitance
5
A_VOL Large-Signal Voltage Gain V_S = 5V, V_O = 75mV to 4.8V,
R_L = 10k
600 3800
CMRR Common Mode
Rejection Ratio
V_S = 5V, V_CM = V⁺ to V^–
V_S = 5V, V_CM = 0.5V to 4.5V
76 90
CMRR Match
(Channel-to-Channel)
(Note 3)
V_S = 5V, V_CM = V⁺ to V^–
V_S = 5V, V_CM = 0.5V to 4.5V 3
75 91
4
60 210
68
85
66
nV_P-P
nV/√Hz
pA/√Hz
pF
5, 6 V/mV
dB
dB
dB
dB
PSRR
Power Supply
Rejection Ratio
PSRR Match
(Channel-to-Channel)
(Note 3)
V_S = 4.5V to 12V,
V_CM = V_O = 0.5V
V_S = 4.5V to 12V,
V_CM = V_O = 0.5V
88 105
3 82 120
1
86 104
80 118
2, 3
dB
dB
V_OL
Output Voltage Swing
(Low) (Note 4)
No Load
I_SINK = 1mA
I_SINK = 2.5mA
V_OH
Output Voltage Swing
(High) (Note 4)
No Load
I_SOURCE = 1mA
I_SOURCE = 2.5mA
I_SC
Short-Circuit Current
V_S = 5V
I_S
Supply Current per Amp
GBW Gain-Bandwidth Product V_S = 5V, f = 100kHz
SR
Slew Rate
V_S = ±2.5V, A_V = –1,
R_L = 10k, V_O = ±2V,
Measure at V_O = ±1V
14 30
4
50 100 4
90 200
2.5 10
4
70 150 4
140 250
±12.5 24
1
1.7 2.2 1
6.8 10.5
2.6 4.5
4
25
75
mV
65 150
5, 6
mV
110 220
mV
5
25
mV
100 250
5, 6
mV
180 300
mV
±5 ±10
2, 3
mA
2
2.7
2, 3
mA
5.8 8.5
MHz
2
3.6
5, 6 V/µs
TABLE 2A: ELECTRICAL CHARACTERISTICS
(Postirradiation) V_S = 5V; V_CM = half supply, T_A = 25°C, unless otherwise noted.
10Krad(Si) 20Krad(Si) 50Krad(Si) 100Krad(Si) 200Krad(Si)
SYMBOL PARAMETER
V_OS
Input Offset Voltage
I_B
Input Bias Current
I_OS
Input Offset Current
Input Voltage Range
A_VOL Large-Signal Voltage
Gain
CMRR Common Mode
Rejection Ratio
CMRR Match
(Channel-to-Channel)
CONDITIONS
V_CM = V⁺, V^–
V_CM = V⁺, V^–
V_CM = V⁺, V^–
V_O = 75mV to V⁺ – 0.2V
R_L = 10k
V_CM = V⁺ to V^–
V_CM = V⁺ to V^–
NOTES MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX UNITS
950
950
950
950
950
µV
700
750
800
850
900
nA
65
65
65
65
65
nA
V^– V⁺ V^– V⁺ V^– V⁺ V^– V⁺ V^– V⁺
V
300
300
300
300
300
V/mV
70
70
70
70
70
dB
3 70
70
70
70
70
dB
PSRR Power Supply
Rejection Ratio
V_S = 4.5V to 12V,
V_CM = V_O = 0.5V
88
88
88
88
88
dB
rh1498mff
4
For more information www.linear.com/RH1498M