LTC3853_15 Datasheet, PDF (30/36 Pages) Linear Technology – Triple Output, Multiphase Synchronous Step-Down Controller

LTC3853
APPLICATIONS INFORMATION
For channel 1, the DCR_SENSE filter/divider values are:
R1= ^{R1|| R2} = ^1100Ω ≅ 4.75k;
R_D
0.23
R2 = ^{R1• RD} = ^{4.75k • 0.23} ≅ 1430Ω
1− R_D 1− 0.23
The power loss in R1 at the maximum input voltage is:
P_LOSSR1=
( V_{IN (MAX )}
− V_OUT
R1
)
•
V_OUT
=
(20V − 5V) •
4.75k
5V
=
15.8mW
The respective values for Channel 2 are R1 = 4.75k, R2 =
1430Ω; and P_LOSSR1 = 11.6mW. And for Channel 3 are
R1 = 2.21k, R2 = 1.82k; and P_LOSSR1 = 10.2mW.
Burst Mode operation is chosen for high light load efficiency
(Figure 14) by floating the MODE/PLLIN pin. Power loss
due to the DCR sensing network is slightly higher at light
loads than would have been the case with a suitable sense
resistor (9mΩ). At heavier loads, DCR sensing provides
higher efficiency.
100
10
DCR
90
9mΩ
80
1
DCR
70
60
0.1
50
40
0.01
EFFICIENCY
POWER LOSS
0.01
0.1
1
10
LOAD CURRENT (A)
3853 F14
Figure 14. Design Example Efficiency vs Load
The power dissipation on the topside MOSFET can be easily
estimated. Choosing a Siliconix Si4816BDY dual MOSFET
results in: R_DS(ON) = 0.023Ω/0.016Ω, C_MILLER @ 100pF.
At maximum input voltage with T(estimated) = 50°C:
P_MAIN
=
5V
20V
(5)²
[¹⁺
(0.005)(50°C
–
25°C)_]
•
(0.023Ω)
+
(20V)²


5A
2


(2Ω)(100pF
)
•


5
1
– 2.3
+
1
2.3
^(500kHz)
=
243mW
A short-circuit to ground will result in a folded back cur-
rent of:
I_SC
=
(1/ 3)75mV
0.009Ω
–
1^
2 
90ns(20V)^
3.3µH 
=
2.5A
with a typical value of R_DS(ON) and d = (0.005/°C)(25)
= 0.125. The resulting power dissipated in the bottom
MOSFET is:
P_SYNC
=
20V – 5V
20V
(2.5A)²
(1.125)(0.016Ω)
= 84mW
which is less than under full-load conditions.
C_IN is chosen for an RMS current rating of at least 2A at
temperature assuming only one channel is on. C_OUT is
chosen with an ESR of 0.02Ω for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
V_ORIPPLE = R_ESR (DI_L) = 0.02Ω(1.5A) = 30mV_P-P
3853fc
30
For more information www.linear.com/LTC3853