English
Language : 

LTC3872-1_15 Datasheet, PDF (3/20 Pages) Linear Technology – No RSENSE Current Mode Boost DC/DC Controller
LTC3872-1
Electrical Characteristics The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 4.2V unless otherwise noted.
PARAMETER
CONDITIONS
MIN TYP MAX UNITS
Input Voltage Range
l 2.75
9.8
V
Input DC Supply Current
Normal Operation
Shutdown
UVLO
Typicals at VIN = 4.2V (Note 4)
2.75V ≤ VIN ≤ 9.8V
VRUN/SS = 0V
VIN < UVLO Threshold
250
400
µA
8
20
µA
20
35
µA
Undervoltage Lockout Threshold
VIN Rising
VIN Falling
l 2.3
2.45 2.75
V
l 2.05
2.3
2.55
V
Shutdown Threshold (at RUN/SS)
VRUN/SS Falling
VRUN/SS Rising
l 0.6
0.85 1.05
V
l 0.65 0.95 1.15
V
Regulated Feedback Voltage
(Note 5) LTC3872-1E
LTC3872-1I and LTC3872-1H
l 1.182 1.2 1.218
V
l 1.178 1.2 1.218
V
Feedback Voltage Line Regulation
2.75V < VIN < 9V (Note 5)
0.14
mV/V
Feedback Voltage Load Regulation
VITH = 1.6V (Note 5)
VITH = 1V (Note 5)
0.05
%
–0.05
%
VFB Input Current
RUN/SS Pull Up Current
Oscillator Frequency
Normal Operation
Gate Drive Rise Time
Gate Drive Fall Time
Peak Current Sense Voltage
(Note 5)
VRUN/SS = 0
VFB = 1V
CLOAD = 3000pF
CLOAD = 3000pF
IPRG = GND (Note 6)
LTC3872-1E
LTC3872-1I
LTC3872-1H
25
50
nA
0.35
0.7
1.25
µA
500
550
650
kHz
40
ns
40
ns
l 90
105
120
mV
l 85
105
120
mV
l 80
105
120
mV
IPRG = Float
LTC3872-1E
LTC3872-1I
LTC3872-1H
l 160
180
200
mV
l 150
180
200
mV
l 145
180
200
mV
IPRG = VIN
LTC3872-1E
LTC3872-1I
LTC3872-1H
l 260
285
310
mV
l 250
285
310
mV
l 240
285
310
mV
Default Internal Soft-Start Time
1
ms
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3872-1 is tested under pulsed load conditions such that
TJ ≈ TA. The LTC3872-1E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3872-1I is guaranteed
over the –40°C to 125°C operating junction temperature range. The
LTC3872-1H is guaranteed over the full –40°C to 150°C operating junction
temperature range. The maximum ambient temperature consistent with
these specifications is determined by specific operating conditions in
conjunction with board layout, the rated package thermal impedance and
other environmental factors.
Note 3: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formula:
LTC3872-1TS8: TJ = TA + (PD • 195°C/W)
LTC3872-1DDB: TJ = TA + (PD • 76°C/W)
Note 4: The dynamic input supply current is higher due to power MOSFET
gate charging (QG • fOSC). See Applications Information.
Note 5: The LTC3872-1 is tested in a feedback loop which servos VFB to
the reference voltage with the ITH pin forced to the midpoint of its voltage
range (0.7V ≤ VITH ≤ 1.9V, midpoint = 1.3V).
Note 6: Rise and fall times are measured at 10% and 90% levels.
For more information www.linear.com/LTC3872-1
38721f
3