LTC3858 Datasheet, PDF (23/38 Pages) Linear Technology – Low IQ, Dual 2-Phase Synchronous Step-Down Controller

LTC3858
Applications Information
A comparator monitors the output for overvoltage condi-
tions. The comparator detects faults greater than 10%
above the nominal output voltage. When this condition
is sensed, the top MOSFET is turned off and the bottom
MOSFET is turned on until the overvoltage condition is
cleared. The bottom MOSFET remains on continuously
for as long as the overvoltage condition persists; if V_OUT
returns to a safe level, normal operation automatically
resumes.
A shorted top MOSFET will result in a high current condition
which will open the system fuse. The switching regulator
will regulate properly with a leaky top MOSFET by altering
the duty cycle to accommodate the leakage.
Phase-Locked Loop and Frequency Synchronization
The LTC3858 has an internal phase-locked loop (PLL)
comprised of a phase frequency detector, a lowpass filter,
and a voltage-controlled oscillator (VCO). This allows the
turn-on of the top MOSFET of controller 1 to be locked to
the rising edge of an external clock signal applied to the
PLLIN/MODE pin. The turn-on of controller 2’s top MOSFET
is thus 180 degrees out of phase with the external clock.
The phase detector is an edge sensitive digital type that
provides zero degrees phase shift between the external
and internal oscillators. This type of phase detector does
not exhibit false lock to harmonics of the external clock.
When not prebiased, applying an external clock will invoke
traditional PLL operation. If the external clock frequency is
greater than the internal oscillator’s frequency, f_OSC, then
current is sourced continuously from the phase detector
output, pulling up the VCO input. When the external clock
frequency is less than f_OSC, current is sunk continuously,
pulling down the VCO input. If the external and internal
frequencies are the same but exhibit a phase difference,
the current sources turn on for an amount of time cor-
responding to the phase difference. The voltage at the
VCO input is adjusted until the phase and frequency of
the internal and external oscillators are identical. At the
stable operating point, the phase detector output is high
impedance and the internal filter capacitor, C_LP , holds the
voltage at the VCO input.
1000
900
800
700
600
500
400
300
200
100
0
15 25 35 45 55 65 75 85 95 105 115 125
FREQ PIN RESISTOR (kΩ)
3858 F09
Figure 9. Relationship Between Oscillator Frequency
and Resistor Value at the FREQ Pin
Note that the LTC3858 can only be synchronized to an
external clock whose frequency is within range of the
LTC3858’s internal VCO, which is nominally 55kHz to 1MHz.
This is guaranteed to be between 75kHz and 850kHz.
Typically, the external clock (on the PLLIN/MODE pin)
input high threshold is 1.6V, while the input low threshold
is 1.1V.
Rapid phase locking can be achieved by using the FREQ
pin to set a free-running frequency near the desired
synchronization frequency. The VCO’s input voltage is
prebiased at a frequency corresponding to the frequency
set by the FREQ pin. Once prebiased, the PLL only needs
to adjust the frequency slightly to achieve phase lock
and synchronization. Although it is not required that the
free-running frequency be near external clock frequency,
doing so will prevent the operating frequency from passing
through a large range of frequencies as the PLL locks.
Table 2 summarizes the different states in which the FREQ
pin can be used.
Table 2
FREQ PIN
0V
INTV_CC
Resistor
Any of the Above
PLLIN/MODE PIN
DC Voltage
DC Voltage
DC Voltage
External Clock
FREQUENCY
350kHz
535kHz
50kHz–900kHz
Phase–Locked to
External Clock
3858fa
23