LT1078 Datasheet, PDF (20/20 Pages) Linear Technology – Micropower, Dual and Quad, Single Supply, Precision Op Amps

LT1078/LT1079
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
0.300 – 0.325
(7.620 – 8.255)
0.009 – 0.015
(0.229 – 0.381)
+0.025
0.325 _–0.015
( ) ^8.255
+0.635
–0.381
0.045 – 0.065
(1.143 – 1.651)
0.065
(1.651)
TYP
0.005
(0.127)
MIN
0.100 ± 0.010
(2.540 ± 0.254)
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.130 ± 0.005
(3.302 ± 0.127)
0.400*
(10.160)
MAX
8
7
6
5
0.125
(3.175)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
0.015
(0.380)
MIN
0.255 ± 0.015*
(6.477 ± 0.381)
12
*THESE DIMENSIONS DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
34
N8 0695
0.300 – 0.325
(7.620 – 8.255)
0.009 – 0.015
(0.229 – 0.381)
+0.025
0.325 _–0.015
( ) ^8.255
+0.635
–0.381
0.130 ± 0.005
(3.302 ± 0.127)
0.015
(0.380)
MIN
0.125
(3.175)
MIN
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.045 – 0.065
(1.143 – 1.651)
0.770*
(19.558)
MAX
14 13 12 11 10 9
0.005
(0.125)
MIN
0.100 ± 0.010
(2.540 ± 0.254)
0.065
(1.651) _{0.255 ± 0.015*}
TYP _{(6.477 ± 0.381)}
0.018 ± 0.003
(0.457 ± 0.076)
1
2
3
4
5
6
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
8
7
N14 0695
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.010
(0.254
–
–
0.020
0.508)
×
45°
0.008 – 0.010
(0.203 – 0.254)
0.016 – 0.050
0.406 – 1.270
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.014 – 0.019
(0.355 – 0.483)
0.004 – 0.010
(0.101 – 0.254)
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
0.050
(1.270)
TYP
1
2
34
*DIMENSION DOES NOT
INCLUDE MOLD FLASH.
MOLD FLASH SHALL NOT
EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT
INCLUDE INTERLEAD
FLASH. INTERLEAD FLASH
SO8 0996 _{SHALL NOT EXCEED 0.010"}
(0.254mm) PER SIDE
0.291 – 0.299**
(7.391 – 7.595)
0.010
(0.254
–
–
0.029
0.737)
×
45°
0.009 – 0.013
(0.229 – 0.330)
NOTE 1
0.016 – 0.050
(0.406 – 1.270)
SW Package
16-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
0.398 – 0.413*
(10.109 – 10.490)
16 15 14 13 12 11 10 9
0.093 – 0.104
(2.362 – 2.642)
0° – 8° TYP
0.050
(1.270)
TYP
0.014 – 0.019
(0.356 – 0.482)
TYP
0.037 – 0.045
(0.940 – 1.143)
NOTE 1
0.004 – 0.012
(0.102 – 0.305)
0.394 – 0.419
(10.007 – 10.643)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES
ON THE BOTTOM OF PACKAGES ARE THE
MANUFACTURING OPTIONS. THE PART MAY
BE SUPPLIED WITH OR WITHOUT ANY OF
THE OPTIONS
123 45678
DIMENSION DOES NOT INCLUDE MOLD
*FLASH. MOLD FLASH SHALL NOT EXCEED
0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE
INTERLEAD FLASH. INTERLEAD FLASH SHALL
S16 (WIDE) 0396 _{NOT EXCEED 0.010" (0.254mm) PER SIDE}
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417^q [phone]
FAX: [phone]^q TELEX: 499-3977 ^q www.linear-tech.com
10789fd LT/TP 0297 5K REV D • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 1994