LT1013 Datasheet, PDF (20/20 Pages) Linear Technology – Quad Precision Op Amp

LT1013/LT1014
PACKAGE DESCRIPTION
H Package
8-Lead TO-5 Metal Can (0.200 PCD)
0.040
(1.016)
MAX
SEATING
PLANE
0.010 – 0.045*
(0.254 – 1.143)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.305 – 0.335
(7.747 – 8.509)
(LTC DWG # 05-08-1320)
0.050
(1.270)
MAX
0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
0.500 – 0.750
(12.700 – 19.050)
REFERENCE
PLANE
45°TYP
0.027 – 0.034
(0.686 – 0.864)
0.016 – 0.021**
(0.406 – 0.533)
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
0.027 – 0.045
(0.686 – 1.143)
0.200
(5.080)
TYP
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
**FOR
SOLDER
DIP
LEAD
FINISH,
LEAD
DIAMETER
IS
0.016
(0.406
–
–
0.024
0.610)
H8(TO-5) 0.200 PCD 0595
NOTE: DIMENSIONS IN INCHES (MILLIMETERS)
T_jmax
150°C
θ_ja
150°C / W
θ_jc
45°C /W
J Package
14-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
CORNER LEADS OPTION
(4 PLCS)
0.005
(0.127)
MIN
0.785
(19.939)
MAX
14 13 12 11 10 9
8
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
0.025
(0.635)
RAD TYP
0.300 BSC
(0.762 BSC)
0.220 – 0.310
(5.588 – 7.874)
1
2
3
4
5
6
7
0.200
(5.080)
MAX
0.015 – 0.060
(0.381 – 1.524)
0.008 – 0.018
(0.203 – 0.457)
0° – 1 5°
0 . 3 8 5± 0 . 0 2 5
( 9 . 7 7 9± 0 . 6 3 5 )
0.045 – 0.068
(1.143 – 1.727)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP OR TIN PLATE LEADS.
0.014 – 0.026
(0.360 – 0.660)
0 . 1 0 0± 0 . 0 1 0
( 2 . 5 4 0± 0 . 2 5 4 )
0.125
(3.175)
MIN
J14 0694
T_jmax
150°C
θ_ja
100°C /W
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.770*
(19.558)
MAX
14 13 12 11 10
9
8
0.255 ± 0.015*
(6.477 ± 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.130 ± 0.005
(3.302 ± 0.127)
1
2
3
4
5
6
7
0.045 – 0.065
(1.143 – 1.651)
0.009 – 0.015
(0.229 – 0.381)
0.015
(0.380)
MIN
+0.025
0.325 _–0.015
( ) ^8.255
+0.635
–0.381
0.125
(3.175)
MIN
0.005
(0.125)
MIN
0.100 ± 0.010
(2.540 ± 0.254)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
T_jmax
100°C
θ_ja
100°C / W
0.065
(1.651)
TYP
0.018 ± 0.003
(0.457 ± 0.076)
N14 0695
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
SW Package
16-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
0.398 – 0.413*
(10.109 – 10.490)
16 15 14 13 12 11 10 9
0.228 – 0.244
(5.791 – 6.197)
0.150 – 0.157**
(3.810 – 3.988)
NOTE 1
0.394 – 0.419
(10.007 – 10.643)
0.010
(0.254
–
–
00..0520_×084)5_°
0.008 – 0.010
(0.203 – 0.254)
0°– 8° T Y P
1
2
0.053 – 0.069
(1.346 – 1.752)
0.016 – 0.050
0.406 – 1.270
0.014 – 0.019
(0.355 – 0.483)
*D I M E N S I O N D O E S N O T I N C L U D E M O L D F L A S H . M O L D F L A S H
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
* *D I M E N S I O N D O E S N O T I N C L U D E I N T E R L E A D F L A S H . I N T E R L E A D
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
34
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
SO8 0695
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone] ^q FAX: [phone] ^q TELEX: 499-3977
0.291 – 0.299**
(7.391 – 7.595)
0.010
(0.254
–
–
0.029
0.737)
×
45°
123 45678
0.093 – 0.104
(2.362 – 2.642)
0.037 – 0.045
(0.940 – 1.143)
0° – 8° TYP
0.050
0.009 – 0.013
(0.229 – 0.330)
NOTE:
NOTE 1
0.016 – 0.050
(0.406 – 1.270)
(1.270)
TYP _{0.014 – 0.019}
(0.356 – 0.482)
TYP
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS.
0.004 – 0.012
(0.102 – 0.305)
S16 (WIDE) 0695
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
LT/GP 0196 REV A • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 1990