LTC3604 Datasheet, PDF (12/24 Pages) Linear Technology – 2.5A, 15V Monolithic Synchronous Step-Down Regulator

LTC3604
APPLICATIONS INFORMATION
highest capacitance density, but it is important to only
use types that have been surge tested for use in switching
power supplies. Aluminum electrolytic capacitors have
significantly higher ESR but can be used in cost-sensitive
applications provided that consideration is given to ripple
current ratings and long-term reliability. Ceramic capacitors
have excellent low ESR characteristics and small footprints.
Their relatively low value of bulk capacitance may require
multiple capacitors in parallel.
Using Ceramic Input and Output Capacitors
Higher value, lower cost ceramic capacitors are now
available in small case sizes. Their high voltage rating
and low ESR make them ideal for switching regulator
applications. However, due to the self-resonant and high-Q
characteristics of some types of ceramic capacitors, care
must be taken when these capacitors are used at the input
and output. When a ceramic capacitor is used at the input,
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
V_IN input. At best, this ringing can couple to the output and
be mistaken as loop instability. At worst, a sudden inrush
of current through the long wires can potentially cause a
voltage spike at V_IN large enough to damage the part. For
a more detailed discussion, refer to Application Note 88.
When choosing the input and output ceramic capacitors
choose the X5R or X7R dielectric formulations. These
dielectrics provide the best temperature and voltage
characteristics for a given value and size.
INTV_CC Regulator Bypass Capacitor
An internal low dropout (LDO) regulator produces a
3.3V supply voltage used to power much of the internal
LTC3604 circuitry including the power MOSFET gate
drivers. The INTV_CC pin connects to the output of this
regulator and must have a minimum of 1μF of decoupling
capacitance to ground. The decoupling capacitor should
have low impedance electrical connections to the INTV_CC
and PGND pins to provide the transient currents required
by the LTC3604. The user may connect a maximum load
current of 5mA to this pin but must take into account the
increased power dissipation and die temperature that
results. Furthermore, this supply is intended only to supply
additional DC load currents as desired and not intended to
regulate large transient or AC behavior, as this may impact
LTC3604 operation.
Boost Capacitor
The boost capacitor, C_BOOST, is used to create a voltage rail
above the applied input voltage V_IN. Specifically, the boost
capacitor is charged to a voltage equal to approximately
INTV_CC each time the bottom power MOSFET is turned
on. The charge on this capacitor is then used to supply
the required transient current during the remainder of the
switching cycle. When the top MOSFET is turned on, the
BOOST pin voltage will be equal to approximately V_IN +
3.3V. For most applications a 0.1μF ceramic capacitor will
provide adequate performance.
Output Voltage Programming
The LTC3604 will adjust the output voltage such that V_FB
equals the reference voltage of 0.6V according to:
V_OUT
=
0.6V
⎛
⎝⎜
1+
R1⎞
R2 ⎠⎟
The desired output voltage is set by appropriate selection of
resistors R1 and R2 as shown in Figure 2. Choosing large
values for R1 and R2 will result in improved efficiency but
may lead to undesirable noise coupling or phase margin
reduction due to stray capacitances at the FB node. Care
should be taken to route the FB line away from any noise
source, such as the SW line.
To improve the frequency response of the main control
loop a feedforward capacitor, C_F, may be used as shown
in Figure 2.
FB
LTC3604
SGND
V_OUT
R1
C_F
R2
3604 F02
Figure 2. Optional Feedforward Capacitor
3604f
12