APXH006A0X-SRZ Datasheet, PDF (4/23 Pages) Lineage Power Corporation – 2.4 - 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 6A output current

Data Sheet
May 20, 2009
Pico TLynx^TM 6A: Non-isolated DC-DC Power Modules
2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 6A output current
General Specifications
Parameter
Calculated MTBF (IO=IO, max, TA=25°C) Telecordia Issue 2, Method
1 Case 3
Weight
Min
Typ
Max
34,602,572
⎯
1.95 (0.0687)
⎯
Unit
Hours
g (oz.)
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter
On/Off Signal Interface
(VIN=VIN, min to VIN, max ; open collector or equivalent,
Signal referenced to GND)
Device with suffix “4” – Positive Logic (See Ordering
Information)
Logic High (Module ON)
Device Symbol
Min
Typ
Max
Unit
Input High Current
All
IIH
⎯
10
µA
Input High Voltage
Logic Low (Module OFF)
All
VIH
1.2
⎯
VIN,max
V
Input Low Current
All
IIL
⎯
⎯
1
mA
Input Low Voltage
All
VIL
-0.3
⎯
0.3
V
Device Code with no suffix – Negative Logic (See Ordering
Information)
(On/OFF pin is open collector/drain logic input with
external pull-up resistor; signal referenced to GND)
Logic High (Module OFF)
Input High Current
All
IIH
―
―
1
mA
Input High Voltage
Logic Low (Module ON)
All
VIH
VIN – 0.8
―
VIN, max
Vdc
Input low Current
All
IIL
―
―
0.2
mA
Input Low Voltage
Turn-On Delay and Rise Times
All
VIL
-0.2
―
VIN – 1.6
Vdc
(VIN=VIN, nom, IO=IO, max , VO to within ±1% of steady state)
Case 1: On/Off input is enabled and then input power is
applied (delay from instant at which VIN = VIN, min until Vo =
All
Tdelay
―
2
―
msec
10% of Vo, set)
Case 2: Input power is applied for at least one second and
then the On/Off input is enabled (delay from instant at
All
Tdelay
―
2
―
msec
which Von/Off is enabled until Vo = 10% of Vo, set)
Output voltage Rise time (time for Vo to rise from
10% of Vo, set to 90% of Vo, set)
All
Trise
―
5
―
msec
Output voltage overshoot (TA = 25^oC
3.0
% VO, set
VIN= VIN, min to VIN, max,IO = IO, min to IO, max)
With or without maximum external capacitance
Over Temperature Protection
(See Thermal Considerations section)
All
Tref
140
°C
Sequencing Delay time
Delay from VIN, min to application of voltage on SEQ
pin
Tracking Accuracy
(Power-Up: 2V/ms)
All
TsEQ-delay
10
APTH VSEQ –Vo
msec
100
mV
(Power-Down: 2V/ms)
APTH VSEQ –Vo
100
mV
(VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo)
LINEAGE POWER
4