X5R0402K Datasheet, PDF (6/8 Pages) KOA Speer Electronics, Inc. – Ceramic Chip Capacitors

SS-241 R5
9. Carrier Tape Specifications
Embossed plastic
8 & 12mm
T2
T
B1
K₀
T1
For tape feeder reference
only including draft
concentric around B0
10 pitches cumulative
tolerance on tape
±0.008 (±0.2)
Deformation
between
embossments
D0
A0
P0
P2
Top
cover
tape
B0
Embossment
E
F
W
G1
See note 3
G2
See note 4
Center lines
of cavity
User direction of feed
P₁
Maximum cavity
size, see note 1
D1 for components
.079 x .047 (2.0 x 1.2)
and larger
Dimensions in inches (mm)
Tape Size
Constant
8mm
and
12mm
D₀
E
.059
±
-
.004
0.0
.069 ± .004
(1.5 ) ± 0.10 (1.75 ±0.10)
- 0.0
Tape Size
B1
Variable Max.
See note 6
8mm
.179
(4.55)
12mm
.323
(8.2)
12mm
1/2 Pitch
.179
(4.55)
12mm
.323
Double Pitch (8.2)
D1
Min.
See note 5
.039
(1.0)
.059
(1.5)
.039
(1.0)
.059
(1.5)
P₀
.157 ± .004
(4.0 ± 0.10)
F
.138 ± .002
(3.5 ± 0.05)
.217 ± .002
(5.5 ± 0.05)
.138 ± .002
(3.5 ± 0.05)
.217 ± .002
(5.5 ± 0.05)
P₂
.079 ± .002
(2.0 ± 0.05)
P1
.157 ± .004
(4.0 ± 0.10)
.157 ± .004
(4.0 ± 0.10)
.079 ± .004
(2.0 ± 0.10)
.315 ± .004
(8.0 ± 0.10)
T Max.
.024
(0.600)
T₁
.004
(0.10)
Max.
R
Min.
See note 2
T2
.984
.098
(25) (2.5 Max.)
1.181
.256
(30) (6.5 Max.)
.984
.098
(25) (2.5 Max.)
1.181
.256
(30) (6.5 Max.)
G₁
.030
(0.75)
Min.
See note 3
G₂
.030
(0.75)
Min.
See note 4
W
.315
±
-
.012
.004
(8.0
) ^{± 0.3}
- 0.1
.472 ± .012
(12.0 ± .30)
A0B0K0
See note 1
See note 1
.315
±
-
.012
.004
(8.0 ± 0.3)
- 0.1
.472 ± .012
(12.0 ± .30)
See note 1
See note 1
Notes:
1. A0, B0 and K0 are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the
component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0 and K0)
must be within .002" (0.05)mm min. and .020" (0.50)mm max. The clearance allowed must also prevent rotation of the component within the
cavity of not more than 20 degrees (see examples A & B).
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to
provide R min. for .472" (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4).
3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape
between the embossed cavity or to the edge of the cavity whichever is less.
PAGE 6 OF 8
Bolivar Drive ^■ P.O. Box 547 ^■ Bradford, PA 16701 ^■ USA ^■ 814-362-5536 ^■ Fax [phone] ^■ www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.