U1230 Datasheet, PDF (6/13 Pages) Agilent(Hewlett-Packard) – Handheld Digital Multimeter (DMM)

06 | Keysight | U1230 Series Handheld Digital Multimeters (DMMs) - Data Sheet
Electrical Specifications
DC specifications
Function
Voltage
Resistance
Diode³
Current⁴
Range
Resolution
600 mV¹
6V
60 V
600 V
600 V (VZ_LOW)²
0.1 mV
0.001 V
0.01 V
0.1 V
0.1 V
600 Ω⁴
6 kΩ⁴
60 kΩ
600 kΩ
6 MΩ⁵
60 MΩ⁵
0.1 Ω
0.001 kΩ
0.01 kΩ
0.1 kΩ
0.001 MΩ
0.01 MΩ
2V
0.001 V
60 μA¹
600 μA¹
6 A^2,5
10 A^{2, 3}
0.01 μA
0.1 μA
0.001 A
0.01 A
Accuracy ±
(% of reading + counts of
least significant digit)
U1231A/U1232A/
U1233A
Test
current
Where
(applicable)
0.5% + 2
NA
0.5% + 2
NA
0.5% + 2
NA
0.5% + 2
NA
2% + 3
NA
Burden
voltage/
shunt
Where
(applicable)
Input
impedance
Where
(applicable)
NA
11.18 MΩ
NA
11.18 MΩ
NA
10.1 MΩ
NA
10 MΩ
NA
3 kΩ
0.9% + 3
0.9% + 3
0.9% + 3
0.9% + 3
0.9% + 3
1.5% + 3
0.9% + 2
1.0% + 2
1.0% + 2
1.0% + 3
1.0% + 3
0.57 mA
NA
NA
57 μA
NA
NA
5.7 μA
NA
NA
570 nA
NA
NA
100 nA/10 MΩ NA
NA
100 nA/10 MΩ NA
NA
0.57 mA
NA
NA
NA
< 2.5 V/1 kΩ NA
NA
< 2.5 V/1 kΩ NA
NA
< 0.2 V/0.005 Ω NA
NA
< 0.4 V/0.005 Ω NA
Notes for DC voltage specifications:
1.  The accuracy of the 600 mV range is specified after the Null function is used to subtract the thermal effect (by shorting the test leads).
2.  For VZ_LOW (low input impedance) measurements, auto-ranging is disabled and the multimeter’s range is set to 600 V in the manual
ranging mode.
Notes for resistance specifications:
1.  Overload protection: 600 Vrms for short circuits with < 0.3 A current.
2.  Maximum open voltage is < +3 V.
3.  Built-in buzzer beeps when the resistance measured is less than 23 Ω ± 10 Ω. The multimeter can capture intermittent measurements longer
than 1 ms.
4.  The accuracy of the 600 Ω to 6 kΩ range is specified after the Null function is used to subtract the test lead resistance and thermal effect (by
shorting the test leads).
5.  For the ranges of 6 MΩ and 60 MΩ, the RH is specified for < 60%.
Notes for diode specifications:
1.  Overload protection: 600 Vrms for short circuits with < 0.3 A current.
2.  Built-in buzzer beeps continuously when the voltage measured is less than 50 mV and beeps once for forward-biased diode or semiconductor
junctions measured between 0.3 V and 0.8 V (0.3 V ≤ reading ≤ 0.8 V).
3.  Open voltage for diode: < +3 V DC.
4.  The maximum display for diode measurements is 2100 counts.
Notes for DC current specifications:
1.  Overload protection for 60 μA to 600 μA range: 600 Vrms for short circuits with < 0.3 A current.
2.  Overload protection for 6 A to 10 A range: 11 A/1000 V; 10 × 38 mm fast-acting fuse.
3.  Specification for 10 A range: 10 A continuous. Add 0.3% to the specified accuracy when measuring signals > 10 A to 20 A for 30 seconds
maximum. After measuring currents > 10 A, cool down the multimeter for twice the duration of the measured time before proceeding with
low current measurements.
4.  Only applicable for the U1232A/U1233A model
5.  DC current between ± (0.6 mA and 1 mA) is not measureable on the U1232A and U1233A models.