CT2-PI1LATD31C Datasheet, PDF (7/8 Pages) JDS Uniphase Corporation – OC-12 SFP Transceiver (Multirate,1310 nm and 1550 nm)

OC-12 SFP TRANSCEIVER
7
Specifications
Parameter
IR-1
LR-1
LR-2
Average output power¹
BOL power output¹
TX operating wavelength
Spectral width²
Side mode suppression ratio (DFB laser)³
Extinction ratio⁴ (BOL)
Extinction ratio⁴ (EOL)
Optical rise and fall times (20 to 80%)⁵
Eye mask of optical output
Eye mask margin (filtered)
Operating receiver wavelength
Jitter generation (peak-to-peak)⁶
Jitter generation (rms)⁶
Power output with transmitter disabled
Receiver sensitivity (BOL, BER=1 x 10^-10, ER=12 dB)
Receiver sensitivity (EOL, BER=1 x 10^-10, ER=10 dB)
Maximum received optical power
Link status response time
Optical path penalty
Dispersion
Receiver reflectance
Minimum optical return loss
BER floor
Reflect into Tx for <1 dB degradation at the receiver
Standard case temperature
Extended case temperature
Bit rate
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Typical
Maximum
Minimum
Minimum
Typical
Maximum
Minimum
Maximum
Minimum
Minimum
Maximum
Maximum
Maximum
Typical
Maximum
Minimum
Typical
Minimum
Minimum
Minimum
Typical
Maximum
Maximum
Maximum
Maximum
Minimum
Maximum
Maximum
-15 dBm
-3 dBm
-3 dBm
-
-1.5 dBm
-1.5 dBm
-8 dBm
1 dBm
1 dBm
-
-2 dBm
-2 dBm
-
-1.5 dBm
-1.5 dBm
-9 dBm
0 dBm
0 dBm
-
1280 nm
1480 nm
-
1310 nm
1550 nm
1356 nm
1335 nm
1580 nm
-
0.3 nm
0.3 nm
4 nm
1 nm
1 nm
-
30 dB
30 dB
-
11.0 dB
11.0 dB
-
12.0 dB
12.0 dB
-
14.0 dB
14.0 dB
8.2 dB
10.0 dB
10.0 dB
500 ps
250 ps
250 ps
Compliant with Bellcore TR-NWT-000253
-
25%
25%
1265 nm
1260 nm
1260 nm
1625 nm
1620 nm
1620 nm
-
40 mUIP-P
40 mUIP-P
-
4 mUIrms
4 mUIrms
-
-50 dBm
-
-
-40 dBm
-40 dBm
-
-30 dBm
-30 dBm
-
-32 dBm
-32 dBm
-28 dBm
-28 dBm
-28 dBm
-8 dBm
-8 dBm
-8 dBm
3 µs
3 µs
3 µs
50 µs
50 µs
50 µs
100 µs
100 µs
100 µs
1 dB
1 dB
1 dB
-
-
-
-
-14 dB
-27 dB
-
-24 dB
-24 dB
10^-15
10^-15
10^-15
-
-24 dB
-24 dB
-5 to 75 °C
-5 to 75 °C
-5 to 75 °C
-40 to 85 °C
-40 to 85 °C
-40 to 85 °C
155 to 622 Mb/s 155 to 622 Mb/s 155 to 622 Mb/s
1. Measured as fiber coupled power into a standard single mode fiber, typical connector repeatability is ±1 dB. LC duplex cables manufactured by Stratos are not
recommended due to a potentially larger window of repeatability.
2. Full spectral width measured 20 dB down from the central wavelength peak under fully modulated conditions.
3. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode in fully modulated conditions.
4. Ratio of logic 1 output power to logic 0 output power under fully modulated conditions with a PRBS 23 data pattern.
5. GR-253-CORE, ITU-T, Recommendation G.957. Tested at STM1, STM4, STM16.
6. Formatted OC-12 pattern with scrambled PRBS payload using an Agilent OmniBer as the optical source driving the CT2 optical receiver. The differential data outputs of
this optical receiver are used as the electrical inputs for the CT2 transmitter which optically drives the OmniBer receiver input to complete the jitter test circuit. This is a 60
second test as recommended in GR-253.