DEIC515 Datasheet, PDF (2/9 Pages) IXYS Corporation – 15 Ampere Low-Side Ultrafast RF MOSFET Driver

DEIC515
Absolute Maximum Ratings (Note 1) 15 Ampere Low-Side Ultrafast RF MOSFET Driver
Parameter
Supply Voltage V_CC / V_CCIN
Value
30V (Note 2)
Parameter
Maximum Junction Temperature
Value
150oC
Input Voltage Level V_IN
All Other Pins
-5V to V_CCIN + 0.3V (Note 2)
-0.3V to (V_CC ,V_CCIN)+0.3V
Operating Temperature Range
-40oC to 85oC
Thermal Impedance (Junction To Case)
θJC
0.13oC/W
Power Dissipation
TAMBIENT ≤ 25C
Tcase ≤ 25C
2W
100W
Storage Temperature
-40°C to 150°C
Soldering Lead Temperature 300°C
(10 seconds maximum)
Electrical Characteristics
Unless otherwise noted, TA = 25° C, 8V < V_CC =V_CCIN < 30V.
All voltage measurements with respect to DGND. DEIC515 configured as described in Test Conditions.
Symbol Parameter
Test Conditions
Min
Typ
Max Units
VIH
High input voltage
VIL
Low input voltage
VIN
Input voltage range
IIN
Input current
VOH
High output voltage
VOL
Low output voltage
ROH
Output resistance
@ Output High
ROL
Output resistance
@ Output Low
IPEAK
Peak output current
IDC
Continuous output
current
fMAX
Maximum frequency
tR
Rise time
tF
tONDLY
tOFFDLY
PWmin
Fall time
On-time propagation
delay
Off-time propagation
delay
Minimum pulse width
0V≤ VIN ≤VCC,VCCIN
IOUT = 10mA, VCC = 15V
IOUT = 10mA, VCC = 15V
VCC,VCCIN = 15V
VCCIN -2
-5
-10
VCC,VCCIN - .025
CL=2nF VCC,VCCIN =15V
CL=1nF VCC,VCCIN =15V VOH=2V to 12V
CL=2nF VCC,VCCIN =15V VOH=2V to 12V
CL=1nF VCC,VCCIN =15V VOH=12V to 2V
CL=2nF VCC,VCCIN =15V VOH=12V to 2V
CL=2nF Vcc=15V
CL=2nF Vcc=15V
FWHM CL=1nF VCC,VCCIN =15V
+3V to +3V CL=1nF VCC,VCCIN =15V
V
0.8
V
VCC + 0.3 V
10
µA
V
0.025
V
0.55
0.85
Ω
0.35
0.85
Ω
15
A
2.5
A
45
MHz
2.5
ns
4.1
ns
2.5
ns
3.9
ns
17.4
18.5
ns
14.6
16
ns
6.4
ns
8.2
ns
Z IN
Input Impeadance
VCC,VCCIN Power supply voltage
f = 1MHz
7960
Ω
8
15
30
V
ICC
Power supply current
VIN = 0V
VIN = VCCIN
0
10
µA
10
µA
Note 1: Operating the device beyond parameters with listed “Absolute Maximum Ratings” may cause permanent damage to the
device. Typical values indicate conditions for which the device is intended to be functional, but do not guarantee specific performance
limits. The guaranteed specifications apply only for the test conditions listed. Exposure to absolute maximum rated conditions for
extended periods may affect device reliability.
Note 2: VccIN / V_IN must be within ±0.3V of V_CC due to the upper P channel switch of the output stage. Conduction will occur when
V_CCIN is less than V_CC resulting in a negative V_GS on this P channel switch.