IS61VPS102436A Datasheet, PDF (8/21 Pages) Integrated Silicon Solution, Inc – 1Mb x 36, 2Mb x 18 36Mb SYNCHRONOUS PIPELINED, SINGLE CYCLE DESELECT STATIC RAM

IS61VPS102436A, IS61LPS102436A,IS61VPS204818A,IS61LPS204818A
TRUTH TABLE^(1-8) (3CE option)
OPERATION
ADDRESS CE CE2 CE2 ZZ ADSP ADSC ADV WRITE OE CLK
DQ
Deselect Cycle, Power-Down None H
X
X
L
X
L
X
X
X L-H High-Z
Deselect Cycle, Power-Down None L
X
L
L
L
X
X
X
X L-H High-Z
Deselect Cycle, Power-Down None L
H
X
L
L
X
X
X
X L-H High-Z
Deselect Cycle, Power-Down None L
X
L
L
H
L
X
X
X L-H High-Z
Deselect Cycle, Power-Down None L
H
X
L
H
L
X
X
X L-H High-Z
Snooze Mode, Power-Down
None X X X H X X X X X X
High-Z
Read Cycle, Begin Burst
External L
L
H
L
L
X
X
X
L L-H
Q
Read Cycle, Begin Burst
External L
L
H
L
L
X
X
X
H L-H High-Z
Write Cycle, Begin Burst
External L
L
H
L
H
L
X
L
X L-H
D
Read Cycle, Begin Burst
External L
L
H
L
H
L
X
H
L L-H
Q
Read Cycle, Begin Burst
External L
L
H
L
H
L
X
H
H L-H High-Z
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
L L-H
Q
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
H L-H High-Z
Read Cycle, Continue Burst
Next H
X
X
L
X
H
L
H
L L-H
Q
Read Cycle, Continue Burst
Next H
X
X
L
X
H
L
H
H L-H High-Z
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X L-H
D
Write Cycle, Continue Burst
Next H
X
X
L
X
H
L
L
X L-H
D
Read Cycle, Suspend Burst
Current X
X
X
L
H
H
H
H
L L-H
Q
Read Cycle, Suspend Burst
Current X
X
X
L
H
H
H
H
H L-H High-Z
Read Cycle, Suspend Burst
Current H
X
X
L
X
H
H
H
L L-H
Q
Read Cycle, Suspend Burst
Current H
X
X
L
X
H
H
H
H L-H High-Z
Write Cycle, Suspend Burst
Current X X
X
L
HHH
L
X L-H
D
Write Cycle, Suspend Burst
Current H X
X
L
XHH
L
X L-H
D
NOTE:
1. X means “Don’t Care.” H means logic HIGH. L means logic LOW.
2. For WRITE, L means one or more byte write enable signals (BWa-h) and BWE are LOW or GW is LOW. WRITE = H for all
BWx, BWE, GW HIGH.
3. BWa enables WRITEs to DQa’s and DQPa. BWb enables WRITEs to DQb’s and DQPb. BWc enables WRITEs to DQc’s and
DQPc. BWd enables WRITEs to DQd’s and DQPd. DQPa-DQPd are available on the x36 version.
4. All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
5. Wait states are inserted by suspending burst.
6. For a WRITE operation following a READ operation, OE must be HIGH before the input data setup time and held HIGH during the
input data hold time.
7. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
8. ADSP LOW always initiates an internal READ at the L-H edge of CLK. A WRITE is performed by setting one or more byte write
enable signals and BWE LOW or GW LOW for the subsequent L-H edge of CLK. See WRITE timing diagram for clarification.
8
Integrated Silicon Solution, Inc.
Rev. B
03/27/08