IS43TR16512A Datasheet, PDF (1/80 Pages) Integrated Silicon Solution, Inc – Programmable CAS Latency

IS43/46TR16512A, IS43/46TR16512AL,
512Mx16 8Gb DDR3 SDRAM
FEATURES
 Standard Voltage: V_DD and V_DDQ = 1.5V ± 0.075V
 Low Voltage (L): VDD and VDDQ = 1.35V + 0.1V, -0.067V
-Backward compatible to 1.5V
 High speed data transfer rates with system
frequency up to 933 MHz
 8 internal banks for concurrent operation
 8n-Bit pre-fetch architecture
 Programmable CAS Latency
 Programmable Additive Latency: 0, CL-1,CL-2
 Programmable CAS WRITE latency (CWL) based
on tCK
 Programmable Burst Length: 4 and 8
 Programmable Burst Sequence: Sequential or
Interleave
 BL switch on the fly
 Auto Self Refresh(ASR)
 Self Refresh Temperature(SRT)
OPTIONS
 Configuration:
512Mx16(dual die)
 Package:
96-ball FBGA (10mm x 14mm)
ADDRESS TABLE
SPEED BIN
SEPTEMBER 2014
 Refresh Interval:
7.8 us (8192 cycles/64 ms) Tc= -40°C to 85°C
3.9 us (8192 cycles/32 ms) Tc= 85°C to 105°C
 Partial Array Self Refresh
 Asynchronous RESET pin
 OCD (Off-Chip Driver Impedance Adjustment)
 Dynamic ODT (On-Die Termination)
 Driver strength : RZQ/7, RZQ/6 (RZQ = 240 Ω)
 Write Leveling
 Operating temperature:
Commercial (T_C = 0°C to +95°C)
Industrial (T_C = -40°C to +95°C)
Automotive, A1 (T_C = -40°C to +95°C)
Automotive, A2 (T_C = -40°C to +105°C)
Parameter
Row Addressing
Column Addressing
Bank Addressing
Ranks
Page size
Auto Precharge
Addressing
BL switch on the fly
512Mx16
A0-A14
A0-A9
BA0-2
2
2KB
A10/AP
A12/BC#
Speed Option
JEDEC Speed Grade
15H
DDR3-1333H
125K
DDR3-1600K
107M
DDR3-1866M
Units
CL-nRCD-nRP
9-9-9
11-11-11
13-13-13
tCK
tRCD,tRP(min)
13.5
13.75
13.91
ns
Note:Faster speed options are backward compatible to slower speed options.
Copyright © 2014 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time
without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised
to obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product
can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use
in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc. – www.issi.com –
1
Rev. A
08/13/2014