SM-BGA-9040 Datasheet, PDF (4/5 Pages) Ironwood Electronics. – Excellent signal integrity at high frequencies

4
5
7
11
10
12
15
17
20
2
1
9
3
5
14
8
19
13
18
16
ITEM
NO.
1
2
3
4
DESCRIPTION
Spring Clamshell lid assembly
Screw, M3 x 12mm, Low Head Cap, SS
Socket Lid
Latch
Material
Steel Music Wire
18-8 Stainless Steel
7075-T6 Aluminum Alloy
7075-T6 Aluminum Alloy
5
Hinge Pin and Snap Ring, 3mm OD, 30mm long, 1045 Stl, Blk
Oxide
AISI 1045 Steel, cold drawn
6
Precision Compression Spring, Zinc-Plated Music Wire, 1/2"
Length, .12" OD, .016" Wire
Zinc Plated Music Wire
7
CBT 23mm Compression plate Ni Plated
7075-T6 Aluminum Alloy
8
SM Socket Base Clamshell 23mm, Hinge on Right side
7075-T6 Aluminum Alloy
9
Compression Screw M24 Hard stop
7075-T6 Aluminum Alloy
10
Ball guide for 23mm 28x28 0.8mm pitch
Kapton Polyimide/Cirlex
11
Dowel Pin, 1/32" x 3/16", SS
12
PCB 23x23mm 28x28 0.8mm pitch BGA602
Chrome Stainless Steel
FR4 Standard
13
SM interposer for 23mm 28x28 1mm pitch BGA602
Silmat
14
BGA602 IC 23mm 0.8mm pitch 28x28 array
FR4 Standard
15
SBT/CBT NI PLT BACKING PLT 23MM
16
#0-80 X .375 LG, SOC HD CAP SCREW, ALLOY STL, BLK
OXIDE
7075-T6, Plate (SS)
Alloy Steel
17 Thread-Locking Cup Point Set Screw 3/8"-16 Thread, 5/16" Long
Alloy Steel
18
Custom Insulation Plate 23mm IC
19
SM IC Guide for 23mm device
20
Oval Point Socket Screw 3/8""-16 Thread, 3/8" Length
Ultem 1000
Torlon 4203
18-8 Stainless Steel
30.7250
23.00 (x4)
6.00
2.10
3.50
Socket Assembly/Calibration Instructions:
1. Align and place the socket base assembly on to the target PCB
2. Secure socket base assembly to the PCB using backing plate and hardware
that is provided with socket.
3. Drop the BGA IC into the socket base assembly-Note Pin A1 orientation.
4. Close the lid and turn the compression screw until it bottom's out on the lid.
5. Remove the Top set screw from the compression screw.
6. Using torque driver and 3/16" hex bit turn the inside calibration set screw to
recommended torque. ( 5 In lbs)
7. Place the nylon patch top set screw to lock the inside set screw position.
8. Once calibrated socket should work at the calibrated height. Repeat calibration if needed.
Description: Socket Assy, Insulation Plate
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.03mm [±0.001"], Pitches (from true position) ±0.025mm [±0.001"], substrate thickness tolerance
±10%, all other tolerances ±0.13mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
SM-BGA-9040 Drawing
Ironwood Electronics, Inc.
Tele: [phone]
www.ironwoodelectronics.com
Material: Material <not specified>
Finish: --
Weight: 136.39
2.00 (x5)
R0.80
2.5 (x4)
5.50 (x8)
25.7250 (x4)
Insulation Plate Specification
STATUS: Released
ENG: V. Panavala
FILE: SM-BGA-9040 Dwg
SHEET: 4 OF 5
DRAWN BY: M. Raske
DATE: 10-16-2013
REV. B
SCALE: 2:1
1.50