AHE28XXS_07 Datasheet, PDF (4/8 Pages) International Rectifier – HYBRID-HIGH RELIABILITY DC/DC CONVERTER

AHE28XXS Series
Specifications
T_CASE = -55°C to +105°C, V_IN = +28V ± 5% unless otherwise specified
Absolute Maximum Ratings
Input Voltage ¹
-0.5V to +50VDC
Power Output
Internally limited, 17.5W typ. for AHE2805S/HB & CH, 22.5W typ. for AHE281XS/HB & CH
Soldering Temperature 300°C for 10 seconds
Temperature Range ^{1 Operating Temperature}
Storage Case Temperature
-55°C to +125°C
-65°C to +135°C
Parameter
Static Characteristic
OUTPUT
Voltage
Current
Ripple
Accuracy
Power¹
REGULATION
Line
Load
INPUT
Voltage Range⁴
Current
Ripple Current
Efficiency
Capacitive Load
Load fault power
dissipation⁵
Isolation
Dynamic
Characteristic
Step Load Changes
Output TC =25°C
Transient
Recovery²
Step Line Changes
Output TC = 25°C
Transient
Recovery²
TURN –ON
Overshoot
Delay³
Load Fault Recovery⁴
Weight
Conditions
-55°C ≤ Tc ≤ +125°C
Vin = 28 Vdc ±5%,CL = 0
Unless otherwise specified
VIN=17 to 40 VDC
IOUT=0 to Full Load
Full Load, DC to 1MHz
TCASE = 25°C, IOUT = 0
VIN = 17 to 40 VDC
TCASE = 25°C
IOUT = 0 to Full Load
Inhibited
No Load
Full Load
TCASE = +25°C
No effect on performance
Short Circuit TC =25°C
Overload TC = 25°C
Input to Output @ 500Vdc
50% Load 100% Load
No Load 50% Load
50% Load No Load
50% Load 100% Load
No Load 50% Load
50% Load No Load
Input step 17 to 40VDC
Input step 40 to 17VDC
Input step 17 to 40VDC
Input step 40 to 17VDC
VIN = 17 to 40VDC
IOUT = 0 to Full Load
VIN = 17 to 40VDC
Standard Package
Flange Package
AHE2805S/HB&CH
AHE2812S/HB&CH
Min
Typ
Max
Min
Typ
Max
AHE2815S/HB&CH
Min
Typ
Max
Units
4.90
5.00
5.10 11.76 12.00 12.24 14.70 15.00 15.30
VDC
0.0
3000
0.0
1667
0.0
1333
mADC
20
60
30
60
30
60
mVp-p
4.95
5.00
5.05 11.88 12.00 12.12 14.85 15.00 15.15
VDC
15
20
20
W
5.0
30
35
mV
10
50
50
120
50
150
17
28
40
17
28
40
17
28
40
VDC
8.0
18
8.0
18
8.0
18
mADC
35
35
35
mADC
20
50
25
50
25
50
mV p-p
80
82
80
83
80
84
%
500
1000
200
1000
200
1000
µF
4.5
4.5
4.5
W
6.0
6.0
6.0
100
100
100
MΩ
±150
-300
+300
25
100
+180
-600
400
400
0
8.0
8.0
55
58
±300
-500
+500
70
200
5.0
+300
1000
800
800
550
10
10
±200
-400
+400
25
500
+180
-600
400
400
300
8.0
8.0
55
58
±300
-500
+500
70
1500
5.0
+500
-1500
800
800
600
10
10
±200
-400
+400
25
500
+180
-600
400
400
300
8.0
8.0
±300
-500
+500
70
1500
5.0
+500
-1500
800
800
500
10
10
55
58
mVpk
mVpk
mVpk
µs
µs
ms
mVpk
mVpk
µs
µs
mVpk
ms
ms
g
Notes to Specifications
1. Above +125°C case temperature, derate output power linearly to 0 at 135°C case.
2. Recovery time is measured from the initiation of the transient to where V_OUT has returned to within ±1.0% of V_OUT at 50% load.
See typical waveforms.
3. Turn-on delay time measurement is for either an application of power at the input or a signal at the shutdown pin.
4. For operation at 16VDC, derate output power by 33%.
5. An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit
protection and is the condition of maximum power dissipation.
4
www.irf.com