ISL28114_11 Datasheet, PDF (9/22 Pages) Intersil Corporation – Single, Dual, Quad General Purpose Micropower, RRIO Operational Amplifiers

ISL28114, ISL28214, ISL28414
Applications Information
Functional Description
The ISL28114, ISL28214 and ISL28414 are single dual and
quad, CMOS rail-to-rail input, output (RRIO) micropower
operational amplifiers. They are designed to operate from single
supply (1.8V to 5.5V) or dual supply (±0.9V to ±2.75V). The parts
have an input common mode range that extends 100mV above
and below the power supply voltage rails. The output stage can
swing to within 15mV of the supply rails with a 10kΩ load.
Input ESD Diode Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. For applications where
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input currents
never exceed 20mA (see Figure 19).
R_F
V+
V_IN-
R_IN-
-
R_IN+ ₊
R_L
R_G
V-
FIGURE 19. INPUT ESD DIODE CURRENT LIMITING
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28114, ISL28214 and ISL28414 are immune to
output phase reversal, even when the input voltage is 1V beyond
the supplies.
Unused Channels
If the application requires less than all amplifiers one channel,
the user must configure the unused channel(s) to prevent it from
oscillating. The unused channel(s) will oscillate if the input and
output pins are floating. This will result in higher than expected
supply currents and possible noise injection into the channel
being used. The proper way to prevent this oscillation is to short
the output to the inverting input and ground the positive input (as
shown in Figure 20).
Power Dissipation
It is possible to exceed the +125°C maximum junction
temperatures under certain load, power supply conditions and
ambient temperature conditions. It is therefore important to
calculate the maximum junction temperature (T_JMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified to remain in the
safe operating area. These parameters are related using
Equation 1:
T_JMAX = T_MAX + θ_JAxPD_MAXTOTAL
(EQ. 1)
where:
• P_DMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PD_MAX)
• PD_MAX for each amplifier can be calculated using Equation 2:
PD_MAX
=
V_S × I_qMAX + (V_S
-
V_O
U
TM
A
X
)
×
V_{----O----U---T---M-----A---X--}
R_L
(EQ. 2)
where:
• T_MAX = Maximum ambient temperature
• θ_JA = Thermal resistance of the package
• PD_MAX = Maximum power dissipation of 1 amplifier
• V_S = Total supply voltage
• I_qMAX = Maximum quiescent supply current of 1 amplifier
• V_OUTMAX = Maximum output voltage swing of the application
• R_L = Load resistance
ISL28114, ISL28214 and ISL28414 SPICE
Model
Figure 21 shows the SPICE model schematic and Figure 22 shows
the net list for the SPICE model. The model is a simplified version
of the actual device and simulates important AC and DC
parameters. AC parameters incorporated into the model are: 1/f
and flatband noise, Slew Rate, CMRR, Gain and Phase. The DC
parameters are IOS, total supply current and output voltage swing.
The model uses typical parameters given in the “Electrical
Specifications” Table beginning on page 4. The AVOL is adjusted
for 90dB with the dominate pole at 125Hz. The CMRR is set 72dB,
f = 80kHz). The input stage models the actual device to present an
accurate AC representation. The model is configured for ambient
temperature of +25°C.
Figures 23 through 30 show the characterization vs simulation
results for the Noise Voltage, Closed Loop Gain vs Frequency,
Large Signal 5V Step Response and CMRR and Open Loop Gain
Phase.
-
+
FIGURE 20. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
9
FN6800.5
June 23, 2011