ISL28107_11 Datasheet, PDF (9/31 Pages) Intersil Corporation – Precision Single, Dual and Quad Low Noise Operational

ISL28107, ISL28207, ISL28407
Electrical Specifications V_S ±5V, V_CM = 0, V_O = 0V, T_A = +25°C, unless otherwise noted. Boldface limits apply over the operating
temperature range, -40°C to +125°C. (Continued)
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(Note 8) TYP (Note 8) UNIT
V_CM
Common Mode Input Voltage
Guaranteed by CMRR test
Range
-3
3
V
CMRR
PSRR
A_VOL
V_OH
V_OL
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Open-Loop Gain
Output Voltage High
V_CM = -3V to +3V
V_S = ±2.25V to ±5V
V_O = -3V to +3V, R_L = 10kΩ to ground
R_L = 10kΩ to ground
R_L = 2kΩ to ground
Output Voltage Low
R_L = 10kΩ to ground
R_L = 2kΩ to ground
115
145
dB
115
145
dB
3,000 40,000
V/mV
3.5
3.7
V
3.2
V
3.3
3.55
V
3.1
V
-3.7
-3.5
V
-3.2
V
-3.55
-3.3
V
-3.1
V
I_S
Supply Current/Amplifier
R_L = Open
0.21
0.29
mA
0.35
mA
I_SC
Output Short-Circuit Current
AC SPECIFICATIONS
(Note 9)
± 40
mA
GBW
THD + N
Gain Bandwidth Product
Total Harmonic Distortion + Noise 1kHz, G = 1, V_O = 2.5V_RMS, R_L = 2kΩ
1
MHz
0.0053
%
TRANSIENT RESPONSE
SR
Slew Rate
A_V = 10, R_L = 2kΩ
0.32
V/µs
t_r, t_f, Small
Rise Time
A_V = 1, V_OUT = 100mV_P-P, R_f = 0Ω, R_L = 2kΩ to
355
ns
Signal
10% to 90% of V_OUT
V_CM
Fall Time
A_V = 1, V_OUT = 100mV_P-P, R_f = 0Ω, R_L = 2kΩ to
370
ns
90% to 10% of V_OUT
V_CM
t_s
Settling Time to 0.1%
A_V = -1, V_OUT = 4V_P-P, R_f = R_g = 2kΩ, R_L = 2kΩ to
12.4
µs
4V Step; 10% to V_OUT
V_CM
Settling Time to 0.01%
A_V = -1, V_OUT = 4V_P-P, R_f = R_g = 2kΩ, R_L = 2kΩ to
22
µs
4V Step; 10% to V_OUT
V_CM
NOTES:
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
9. Output Short Circuit Current is the minimum current (source or sink) when the output is driven into the supply rails with R_L = 0Ω to ground.
9
FN6631.4
September 6, 2011