English
Language : 

ISL54217_09 Datasheet, PDF (6/21 Pages) Intersil Corporation – USB 2.0 High-Speed x 2Channels/Stereo Audio Dual SP3T (Dual 3-to-1 Multiplexer)
◁
ISL54217
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VC0H, VC1H = 1.4V, VC0L, VC1L= 0.5V,
(Note 8), Unless Otherwise Specified. (Continued)
PARAMETER
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Notes 9, 10) TYP (Notes 9, 10) UNITS
2D+/2D- OFF Capacitance,
C2D+OFF, C2D-OFF
f = 1MHz, VDD = 3.3V, C0 = VDD, C1 = VDD, Tx or
25
-
3
-
pF
Rx = COMx = 0V (see Figure 5)
COM ON Capacitance, CCOM-(ON), f = 1MHz, VDD = 3.0V, USB1 mode (C0 = 0V, C1 = VDD) 25
-
8
-
pF
CCOM+(ON)
or USB2 Mode (C0 = VDD, C1 = 0V) (see Figure 5)
POWER SUPPLY CHARACTERISTICS
Power Supply Range, VDD
Positive Supply Current, IDD
(ALL OFF Mode)
VDD = 3.6V, C1 = GND, C0 = GND
Full
2.7
4.6
V
25
-
6.2
8
µA
Full
-
-
15
µA
Positive Supply Current, IDD
(USB1 Mode)
Positive Supply Current, IDD
(USB2 Mode)
Positive Supply Current, IDD
(Audio Mode)
VDD = 3.6V, C1 = GND, C0 = VDD
VDD = 3.6V, C1 = VDD, C0 = GND
VDD = 3.6V, C0 = C1 = VDD)
25
-
6.5
8
µA
Full
-
-
15
µA
25
-
6.2
8
µA
Full
-
-
15
µA
25
-
9
14
µA
Full
-
-
20
µA
Positive Supply Current, IDD
(MUTE Mode)
VDD = 3.6V, C1 = VDD, C0 = GND
25
-
6.6
8
µA
Full
-
-
15
µA
Power OFF COMx Current, ICOMx VDD = 0V, C0 = C1 = Float, COMx = 5.25V
Power OFF Logic Current, IC0,IC1 VDD = 0V, C0 = C1 = 5.25V
Power OFF D+/D- Current, IXD+, IXD- VDD = 0V, C0 = C1 = Float, XD- = XD+ = 5.25V
DIGITAL INPUT CHARACTERISTICS
25
-
-
1
µA
25
-
11
-
µA
25
-
5
-
µA
C0, C1 Voltage Low, VC0L, VC1L VDD = 2.7V to 3.6V
Full
-
-
0.5
V
C0, C1 Voltage High, VC0H, VC1H VDD = 2.7V to 3.6V
Full
1.4
-
5.25
V
C0, C1 Input Current, IC0L, IC1L
VDD = 3.6V, C0 = C1= 0V or Float
Full
-50
6.2
50
nA
C0, C1 Input Current, IC0H, IC1H VDD = 3.6V, C0 = C1= 3.6V
Full
-2
1.6
2
µA
C0, C1 Pull-Down Resistor, RCx
VDD = 3.6V, C0 = C1= 3.6V, Measure current into C0 or C1 Full
-
4
-
MΩ
pin and calculate resistance value.
NOTES:
8. VLOGIC = Input voltage to perform proper function.
9. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
10. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
11. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
12. Limits established by characterization and are not production tested.
13. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON
value, between L and R or between 1D+ and 1D- or between 2D+ and 2D-.
6
FN6817.3
May 4, 2009
 ▷