English
Language : 

ISL54062 Datasheet, PDF (6/16 Pages) Intersil Corporation – 1.8V to +6.5V, Sub-Ohm, Dual SPDT Analog Switch with Negative Signal Capability and Click and Pop Elimination
◁
ISL54062
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, VINH = 1.0V, VINL = 0.4V (Note 9), Unless Otherwise
Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 1.8V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V) 25
-
1.87
-
Ω
to V+, (see Figure 5)
Full
-
1.97
-
Ω
rON Matching Between
V+ = 1.8V, ICOM = 100mA, VNO or VNC = Voltage at 25
-
16
-
mΩ
Channels, ΔrON
max rON (Note 13)
Full
-
30
-
mΩ
rON Flatness, RFLAT(ON)
V+ = 1.8V, ICOM = 100mA, VNO or VNC = (V+ - 6.5V) 25
-
1.34
-
Ω
to V+ (Note 12)
Full
-
1.43
-
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 1.8V, VNO or VNC = 1.8V, RL = 50Ω, CL = 35pF 25
-
145
-
ns
(see Figure 1)
Full
-
150
-
ns
Turn-OFF Time, tOFF
V+ = 1.8V, VNO or VNC = 1.8V, RL = 50Ω, CL = 35pF 25
-
20
-
ns
(see Figure 1)
Full
-
22
-
ns
Break-Before-Make Time Delay, V+ = 1.8V, VNO or VNC = 1.8V, RL = 50Ω, CL = 35pF Full
tD
(see Figure 3)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω (see Figure 2)
25
-3dB Bandwidth
VCOM = 1VRMS, RL = 50Ω, CL = 5pF
25
NOx or NCx OFF Capacitance, f = 1MHz
25
COFF
COMx ON Capacitance,
f = 1MHz (see Figure 7)
25
CCOM(ON)
DIGITAL INPUT CHARACTERISTICS
-
130
-
-
40
-
-
60
-
-
36
-
-
88
-
ns
pC
MHz
pF
pF
Input Voltage Low, VINL
25
-
-
0.4
V
Input Voltage High, VINH
25
1.0
-
-
V
Input Current, IINH, IINL
V+ = 2.0V, VIN = 0V or V+
25
-0.5
-
0.5
µA
Input Current, IINH, IINL
V+ = 2.0V, VIN = 0V or V+
Full
-
0.38
-
µA
NOTES:
9. VIN = input voltage to perform proper function.
10. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
11. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
12. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
13. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON
value, between NC1 and NC2 or between NO1 and NO2.
14. Limits established by characterization and are not production tested.
6
FN6581.0
February 25, 2009
 ▷