HCS190MS Datasheet, PDF (6/9 Pages) Intersil Corporation – Radiation Hardened Synchronous 4-Bit Up/Down Counter

Specifications HCS190MS
TABLE 6. APPLICABLE SUBGROUPS
CONFORMANCE GROUPS
METHOD
GROUP A SUBGROUPS
Initial Test (Preburn-In)
100%/5004
1, 7, 9
Interim Test I (Postburn-In)
100%/5004
1, 7, 9
Interim Test II (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Interim Test III (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Final Test
100%/5004
2, 3, 8A, 8B, 10, 11
Group A (Note 1)
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11
Group B
Subgroup B-5
Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas
Subgroup B-6
Sample/5005
1, 7, 9
Group D
Sample/5005
1, 7, 9
NOTE:
1. Alternate group A testing in accordance with Method 5005 of Mil-Std-883 may be exercised.
READ AND RECORD
ICC, IOL/H, IOZL/H
ICC, IOL/H, IOZL/H
ICC, IOL/H, IOZL/H
ICC, IOL/H, IOZL/H
Subgroups 1, 2, 3, 9, 10, 11
TABLE 7. TOTAL DOSE IRRADIATION
CONFORMANCE
GROUPS
METHOD
PRE RAD
Group E Subgroup 2
5005
1, 7, 9
NOTE:
1. Except FN test which will be performed 100% go/no-go.
TEST
POST RAD
Table 4
READ AND RECORD
PRE RAD
POST RAD
1, 7, 9
Table 4 (Note 1)
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS
OPEN
STATIC I BURN-IN (Note 1)
2, 3, 6, 7, 12, 13
STATIC II BURN-IN (Note 1)
2, 3, 6, 7, 12, 13
GROUND
1, 4, 5, 8, 9, 10,
11, 14, 15
8
1/2 VCC = 3V ± 0.5V
-
-
DYNAMIC BURN-IN (Note 2)
-
1, 4, 5, 8, 9, 10, 15
2, 3, 6, 7, 12, 13
NOTES:
1. Each pin except VCC and GND will have a series resistor of 10K ± 5%.
2. Each pin except VCC and GND will have a series resistor of 1K ± 5%.
VCC = 6V ± 0.5V
16
1, 4, 5, 9, 10, 11, 14,
15, 16
11, 16
OSCILLATOR
50kHz
25kHz
-
-
-
-
14
-
TABLE 9. IRRADIATION TEST CONNECTIONS
OPEN
GROUND
VCC = 5V ± 0.5V
2, 3, 6, 7, 12, 13
8
1, 4, 5, 9, 10, 11, 14, 15, 16
NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing. Group E,
Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number 518836
265