ISL54503 Datasheet, PDF (5/13 Pages) Intersil Corporation – +1.8V to +5.5V, 2.5OHM, Single SPDT Analog Switch

ISL54503
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V
(Note 10), Unless Otherwise Specified. Boldface limits apply over the operating
temperature range, -40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
Total Harmonic Distortion f = 20Hz to 20kHz, V_COM = 2V_P-P,
R_L = 600Ω
-3dB Bandwidth
Signal = 0dBm, R_L = 50Ω
NO or NC OFF Capacitance, f = 1MHz, V_NO or V_NC = V_COM = 0V
C_OFF
(see Figure 7)
COM ON Capacitance,
C_COM(ON)
f = 1MHz, V_NO or V_NC = V_COM = 0V
(see Figure 7)
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V+ = 3.6V, V_IN = 0V or V+
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
V+ = 3.6V, V_IN = 0V or V+
TEMP
MIN
(°C) (Notes 11, 12)
25
-
TYP
0.03
MAX
(Notes 11, 12) UNITS
-
%
25
-
250
-
MHz
25
-
6
-
pF
25
-
18
-
pF
25
-
0.013
-
µA
Full
-
0.7
-
µA
Full
-
-
0.5
V
Full
1.4
-
-
V
Full
-0.1
0.058
0.1
µA
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, V_INH = 1V, V_INL = 0.4V (Note 10), Unless
Otherwise Specified. Boldface limits apply over the operating temperature
range, -40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 11, 12) TYP (Notes 11, 12) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range,
V_ANALOG
Full
0
-
V+
V
ON-Resistance, r_ON
V+ = 1.8V, I_COM = 10mA, V_NO or V_NC = 0V 25
-
6
6.5
Ω
to V+, (Note 14, See Figure 5)
Full
-
-
7
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 1.8V, V_NO or V_NC = 1.5V, R_L = 50Ω,
25
-
65
-
ns
C_L = 35pF (see Figure 1, Note 14)
Full
-
95
-
ns
Turn-OFF Time, t_OFF
V+ = 1.8V, V_NO or V_NC = 1.5V, R_L = 50Ω,
25
-
40
-
ns
C_L = 35pF (see Figure 1, Note 14)
Full
-
65
-
ns
Break-Before-Make Time
V+ = 1.8V, V_NO or V_NC = 1.5V, R_L = 50Ω,
Full
-
44
-
ns
Delay, t_D
C_L = 35pF (see Figure 3, Note 14)
Charge Injection, Q
V_G = 0, R_G = 0Ω, C_L = 1.0nF (see Figure 2) 25
-
8.2
-
pC
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
NOTES:
Full
-
-
0.4
V
Full
1
-
-
V
10. V_IN = input voltage to perform proper function.
11. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data
sheet.
12. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
13. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal
range.
14. Limits established by characterization and are not production tested.
5
FN6551.2
October 26, 2009