ISL54503 Datasheet, PDF (4/13 Pages) Intersil Corporation – +1.8V to +5.5V, 2.5OHM, Single SPDT Analog Switch

ISL54503
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V_INH = 2.0V, V_INL = 0.8V
(Note 10), Unless Otherwise Specified. Boldface limits apply over the operating
temperature range, -40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 11, 12) TYP (Notes 11, 12) UNITS
Total Harmonic Distortion f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 32Ω 25
Total Harmonic Distortion f = 20Hz to 20kHz, V_COM = 2V_P-P,
25
R_L = 600Ω
-3dB Bandwidth
R_L = 50Ω
25
NO or NC OFF Capacitance, V+ = 4.5V, f = 1MHz, V_NO or V_NC = V_COM = 25
C_OFF
0V (see Figure 7)
COM ON Capacitance,
C_COM(ON)
V+ = 4.5V, f = 1MHz, V_NO or V_NC = V_COM = 25
0V (see Figure 7)
POWER SUPPLY CHARACTERISTICS
-
0.15
-
-
0.014
-
-
250
-
-
7
-
-
18
-
%
%
MHz
pF
pF
Power Supply Range
Full
1.65
-
5.5
V
Positive Supply Current, I+ V+ = 5.5V, V_IN = 0V or V+
25
-
0.028
0.1
µA
Full
-
1.1
2.5
µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
V+ = 5.5V, V_IN = 0V or V+
Full
-
-
0.8
V
Full
2.4
-
-
V
Full
-0.1
0.053
0.1
µA
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V
(Note 10), Unless Otherwise Specified. Boldface limits apply over the operating
temperature range, -40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 11, 12) TYP (Notes 11, 12) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range,
Full
0
-
V+
V
V_ANALOG
ON-Resistance, r_ON
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V 25
-
3.3
3.5
Ω
µTDFN
to V+, (Note 14, See Figure 5)
Full
-
-
4.5
Ω
ON-Resistance, r_ON
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V 25
-
3.3
3.6
Ω
SOT-23
to V+, (Note 14, See Figure 5)
Full
-
-
4.5
Ω
r_ON Matching Between
Channels,
Δr_ON
V+ = 2.7V, I_COM = 100mA, V_NO or
V_NC = 1.5V (Note 14)
25
-
0.006
0.15
Ω
Full
-
-
0.2
Ω
r_ON Flatness, r_FLAT(ON)
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V 25
-
µTDFN
to V+, (Notes 13, 14)
Full
-
1
1.1
Ω
-
1.2
Ω
r_ON Flatness, r_FLAT(ON)
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V 25
-
SOT-23
to V+, (Notes 13, 14)
Full
-
1
1.2
Ω
-
1.3
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω,
25
-
30
-
ns
C_L = 35pF (see Figure 1, Note 14)
Full
-
30
-
ns
Turn-OFF Time, t_OFF
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω,
25
-
20
-
ns
C_L = 35pF (see Figure 1, Note 14)
Full
-
20
-
ns
Break-Before-Make Time V+ = 3.0V, V_NO or V_NC = 1.5V, R_L = 50Ω, Full
-
18
-
ns
Delay, t_D
C_L = 35pF (see Figure 3, Note 14)
Charge Injection, Q
V_G = 0V, R_G = 0Ω, C_L = 1.0nF (see Figure 2) 25
-
16
-
pC
OFF-Isolation
R_L = 50Ω, C_L = 5pF, f = 1MHz, V_COM =
25
-
70
-
dB
1V_P-P (see Figure 4)
Total Harmonic Distortion f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 32Ω 25
-
0.36
-
%
4
FN6551.2
October 26, 2009